Votos - 6, Puntuación media: 4
(
)
)
|
Resumen del manual
CONNECTIONS ANTENNA CONNECTIONS . Each antenna should be connected to the designated terminals correctly, referring to the following figure. . Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may result in improvement. Outdoor FM antenna Outdoor AM antenna AM loop antenna (included) 75-ohm antenna adapter Indoor FM antenna (included) 75-ohm 300-ohm feeder 75W UNBAL. FM ANT GND AM ANT 75-ohm/300-ohm Ground coaxial cable antenna adapter English Connecting the indoor FM antenna Connecting the AM loop antenna 132 Orient so that the best reception is obtained. * If you connect an outdoor FM antenna to this unit, do not connect the indoor FM antenna to this unit. * The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall. * The AM loop antenna should be kept connected, even if an outdoor AM antenna is connected to this unit. . Optional outdoor FM antenna Consult with your dealer or authorized service center about the best method of selecting and erecting an outdoor FM antenna. The choice of the feeder cable is also important. Flat ribbon- shaped twin-lead cable performs well electrically, and is cheaper and somewhat easier to handle when routing it through windows and around rooms. Coaxial cable is more expensive, does a much better job of minimizing interference, is less prone to the effects of weather and close-by metal objects, and is nearly as good a signal conductor as feeder cable, particularly for foam-type coaxial cables. Coaxial cable is somewhat more difficult to install at the point where the cable enters the building. If coaxial cable is selected, make sure the antenna is designed to be used with that type of cable. 300-ohm feeder 75-ohm coaxial cable cable . Optional outdoor AM antenna In steel buildings or at a great distance from the transmitter, it may be necessary to install an outside long wire antenna. * Use a 75-ohm/300-ohm antenna adapter (not included) or a 75-ohm antenna adapter (not included) for connections. 300-ohm feeder cable 75-ohm coaxial cable 75-ohm/300-ohm antenna adapter 75-ohm antenna adapter 75-ohm coaxial cable Notes for FM antenna installation . To minimize automobile ignition noise, locate the antenna as far from heavy traffic as possible. . Keep the feeder cable or coaxial cable as short as possible. Do not bundle or roll up excess cable. . The antenna should be at least two meters (6.6 feet) from reinforced concrete walls or metal structures. GND terminal For maximum safety and minimum interference, connect the GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth. CONNECTING TO THE AMPLIFIER l Before making any connections, switch OFF the power to l If you have a YAMAHA amplifier whose terminals on the this unit and the amplifier or other component. rear panel are numbered as 1, 2, 3, etc., connections can l Be sure that the connections from the left (“L”) and right be made easily by making sure to connect the LINE OUT (“R”) LINE OUT terminals are connected to the terminals of this unit to the input terminals of the amplifier corresponding (left and right) input terminals of the amplifier numbered 2. or other component. 75W UNBAL. FM ANT GND AM ANT LINE OUT R L 2 TUNER L R Amplifier Connection cord (included) This unit To AC outlet NOTES ABOUT CONTROLLING THIS UNIT WITH THE REMOTE CONTROL TRANSMITTER This unit has a remote control sensor. It receives signals from a remote control transmitter provided with a YAMAHA amplifier. 30° 30° Within approximately 6 m (19.7 feet) Remote control sensor Notes . There should be no large obstacles between the remote control transmitter and the main unit. . If the remote control sensor is directly illuminated by strong lighting (especially an inverter type of fluorescent lamp etc.), it might cause the remote control transmitter not to work correctly. In this case, reposition the main unit to avoid direct lighting. FRONT PANEL COMPONENTS AND THEIR FUNCTIONS Front panel 1 2 34 56 English MHz MEMO PS STEREO 0 20 l00 PTY HOLD EON NEWS INFO AFFAIRS SPORT AUTO RT CTPTYPOWER RDS MODE/FREQ PTY SEEK MODE START AUTO/MAN'L MONO EON FM/AM TUNING MODE 1MEMORY EDIT NATURAL SOUND AM/FM STEREO TUNER TX-590RDS MAN'L/AUTO FM A/B/C/D/E 2 PRESET STATIONS 3 TUNING PTY SELECTOR 4 5 6 7 8 7890A B 1POWER switch Press this switch to switch the power on. Press it again to switch the power off. 2Display panel Shows station frequencies and various information. (Refer to the next page for details.) 3MEMORY (MAN’L/AUTO FM) button When this button is pressed, the MEMO indicator flashes for about 5 seconds. During this period, press the desired PRESET STATIONS button to enter the displayed station into the memory. When this button is pressed a...