Votos - 1, Puntuación media: 3
(
)
)
|
Resumen del manual
* When you select TUNER, PHONO, CD, AUX or TAPE 1/MD, make sure that TAPE 2 MONITOR is not also selected. TUNER CDPHONO AUX TAPE 1/MDTAPE 2 MONITOR 2 Play the source and then turn the VOLUME control up to confirm the input source. (For detailed information on the tuning operations, refer to the page 17.) l6 20 28 40 60 l2 8 4 2 0 –dB VOLUME 3 Begin recording on the tape deck (or MD recorder etc.) connected to this unit. 4 If the tape deck (or MD recorder etc.) connected to the TAPE 2 terminals on the rear of this unit is used for recording, you can monitor the sounds being recorded by pressing TAPE 2 MONITOR so that the “TAPE MON 2” indicator lights up on the display. TUNER CDPHONO AUX TAPE 1/MDTAPE 2 MONITOR Note VOLUME, BASS, TREBLE, BALANCE and LOUDNESS controls have no effect on the material being recorded. Selecting the SPEAKER system Adjusting the continuously variableLOUDNESS control Because one or two speaker systems can be connected to this unit, the SPEAKERS switches allow you to select speaker system A or B, or both at once. SPEAKERS AB ON OFF Adjusting the BALANCE control Adjust the balance of the output volume to the left and right speakers to compensate for sound imbalance caused by speaker location or listening room conditions. BALANCE 0 l l 22 3 3 44 L5 5R Adjusting the BASS and TREBLEcontrols BASS TREBLE 00 ll ll 2 22 2 3 33 3 444 4 55 55 BASS : Turn this clockwise to increase (or counterclockwise to decrease) the low frequency response. TREBLE : Turn this clockwise to increase (or counterclockwise to decrease) the high frequency response. This control provides compensation for the human ears’ loss of sensitivity to high and low-frequency ranges at low volume. This control is adjustable to retain full tonal range at any volume level. 1 LOUDNESS FLAT l –30dB 2 l0 3 9 Set to the “FLAT” position. 48 57 6 VOLUME 2 l6 20 28 40 60 l2 8 4 2 0 –dB Set to the loudest listening level that you would listen in. 3 LOUDNESS l FLAT Turn until the desired volume is –30dB 2 l09 gained. 3 48 57 6 Using the PURE DIRECT switch RX-496RDS and RX-496 only You can enjoy the purest possible sound from your audio sources by pressing this switch so that the indicator lights up. By doing so, the audio signal bypasses the BASS, TREBLE, BALANCE and LOUDNESS controls, eliminating any alteration to the audio signal. To cancel this function, press it again so that the indicator goes off. Indicator PURE DIRECT TUNING OPERATIONS Normally, if station signals are strong and there is no interference, quick automatic-search tuning (AUTOMATIC TUNING) is possible. However, if signals of the station you want to select are weak, you must tune to it manually (MANUAL TUNING). English STANDBY/ON NATURAL SOUND STEREO RECEIVER SPEAKERSPHONES A ON B OFF BASS TREBLE BALANCE VOLUME 5 5 4 3 2 l 0 l 2 3 4 5 5 4 3 2 l 0 l 2 3 4 L R l6 20 28 40 60 l2 8 4 2 0 –dB 5 5 4 3 2 l 0 l 2 3 4 FM/AM MAN’L/AUTO FM TUNING MODE AUTO/MAN’L MONO DOWN TUNING UP MEMORY EDIT A/B/C/D/E 1 2 3 4 5 6 7 8 TUNER CDPHONO AUX TAPE 1/MDTAPE 2 MONITOR LOUDNESS 5 6 7 4 3 2 l FLAT l0 –30dB 9 8 124 3 AUTOMATIC TUNING MANUAL TUNING 1 Select “TUNER” as the input source. TUNER CDPHONO 2 Select the reception band (FM or AM) confirming it on the display. FM/AM or 3 TUNING MODE AUTO/MAN’L MONO AUTO 4 To tune to a higher frequency, press the right side once. To tune to a lower frequency, press the left side once. * If the station where tuning search stops is not the desired one, press again. * If the tuning search does not stop at the desired station (because the signals of the station are weak), change to the MANUAL TUNING method. DOWN TUNING UP 1 Select “TUNER” as the input source. TUNER CDPHONO 2 Select the reception band (FM or AM) confirming it on the display. or FM/AM 3 TUNING MODE AUTO/MAN’L MONO Turn the “AUTO” indicator off. 4 Tune to a desired station manually. * To continue tuning search, hold down the button. DOWN TUNING UP Notes • If you tune to an FM station manually, it is received in monaural mode automatically to increase the signal quality. • RX-496RDS and RX-396RDS only When tuned in to a station, the frequency of the received station is shown on the display. If an RDS station that employs PS data service is received, the frequency is then replaced by the station name. Refer to page 23 for details. PRESET TUNING MANUAL PRESET TUNING This unit can store station frequencies selected by tuning operation. With this function, you can recall any desired station only by selecting the preset station number where it is stored. Up to 40 stations (8 stations x 5 groups) can be stored. STANDBY/ON NATURAL SOUND STEREO RECEIVER SPEAKERSPHONES A ON B OFF BASS TREBLE BALANCE VOLUME 5 5 4 3 2 l 0 l 2 3 4 5 5 4 3 2 l 0 l 2 3 4 L R l6 20 28 40 60 l2 8 4 2 0 –dB 5 5 4 3 2 l 0 l 2 3 4 FM/AM MAN’L/AUTO FM TUNING MODE AUTO/MAN’L MONO DOWN TUNING UP MEMORY EDIT A/B/C/D/E 1 2 3 4 5 6 7 8 TUNER CDPHONO AUX TAPE 1/MDTAPE 2 MONITOR LOUDNESS 5 6 7 4 3 2 l FLAT l0 –30dB 9 8 2, 1 4, 2 3 To sto...
Otros modelos de este manual:El receptor y el amplificador - RX-396RDS (419.77 kb)