Votos - 4, Puntuación media: 3.8
(
)
)
|
Resumen del manual
The sleep timer period can be set in 10-minute steps up to 90 minutes. Press the SLEEP key repeatedly until the desired period before turning the receiver OFF (standby mode) is displayed. • Each press increments the sleep timer period by 10 minutes. 10 = 20 = 30 .....70 = 80 = 90 = Cancel = 10 = 20 = ... The “SLEEP” indicator lights up L SL SR C R SP MUTE A B CLIP LFE DIGITAL DOLBY DIGITAL STEREO SLEEP AUTO DETECT • Pressing the SLEEP key after the sleep timer has started allows you to check the remaining time period. • To cancel the sleep timer, turn the receiver OFF (standby mode) or press the SLEEP key repeatedly until the Sleep timer indicator disappears. Basic remote control operations for KENWOOD DVD players DVD player operation keys The remote control of this unit can control KENWOOD DVD players directly without using the remote control supplied with the DVD player. DV-4900, DV-4070B, DV-2070, DV-203, DVF-9010, DVF-K7010, DVF-5010, DVF-R9030, DVF-R7030, DVF-3530, DV-402, DV-5900, DV-5700, DVF-R9050, DVF-J6050, DV-505, DV-503, DV-502, DVF-3550, DVF-3050, DVF-R4050, DVF-605, DV-6050, DVF-R5060, DVF-3060, DVF-3060K, DV-705, DVF-R5070, DVF-3070, DVF-3080, DVF-N7080, DVF-8100, DVF-3200 and DVF-3250. How to operate the DVD player with the remote control 1. Press the DVD key to turn the DVD player on. 2. Press the CD/DVD key or DVD/6CH key to operate the functions of the DVD player. 3. Press each key for DVD player operation. Refer to the instruction manual of the DVD players for the detailed operating instructions. (To return to the receiver operation mode, press other Input Selector key.) DVD player operation keys You can perform these basic operations using the keys described below when connected to KENWOOD DVD player. STANDBY RECEIVER ON DVD TONE SOUND SLEEP SETUPDIMMER ANGLE REPEAT SUBTITLEAUDIO VO LUME ENTER BAND AUTO/MONO MUTE P.CALL TUNING DVD/6CH VIDEO 1 VIDEO 2 VIDEO 3 AV AU X DISC SEL. PHONOMD/TAPE CD/DVD ACTIVE EQ IMPUT MODETUNER PAGE RDS DISP. PTY BASS BOOST DSP MODE LOUDNESSSTEREOLISTEN MODE RC-R0731E TO P MENU RETURN ON SCREEN MENU – CHANNEL + REMOTE CONTROL UNIT MULTI MULTI Numeric keys (Select tracks) 3/8 (Play/Pause) . (Skip) 4 (Skip) TOP MENU (Title) RETURN 8 (Pause) DIMMER SETUP MENU %(Cursor up) fi(Cursor down) @(Cursor left) #(Cursor right) ENTER 7 (Stop) 1 (Search) . (Search) DISC SEL. (Disc selection) PAGE %/fi (Page up or down) 33 EN In case of difficulty Resetting the Microcomputer The microcomputer may malfunction (unit cannot be operated, or Unplug the power cord from the wall outlet, then plug it shows an erroneous display) if the power cord is unplugged while back in while holding down the (POWER ON/STANDBY) the power is ON, or due to some other external factor. If this key. happens, execute the following procedure to reset the microcomputer and return the unit to its normal operating condition. • Please note that resetting the microcomputer will clear the contents of the memory and returns the unit to the state it was in when it left the factory. Amplifier Symptom Cause Remedy No sound from the speakers. • The speaker cords are disconnected. • VOLUME is set to the minimum position. • MUTE is ON. • The SPEAKERS switches are set to OFF. • Headphones are connected to the PHONES jack. • Connect them properly referring to “Connecting the speakers” % •Adjust the volume to a proper level. • Turn OFF the MUTE. . • Set the SPEAKERS switches to ON. ) • Unplug the headphones plug. ™ The STANDBY indicator blinks and sound is not output. • Speaker cords are short-circuited. • Turn the power off, eliminate the shortcircuiting, then turn on the power again. Sound is not output from one of the speakers. • The speaker cord is disconnected. • The speaker is not set up correctly. • Connect it properly referring to “Connecting the speakers”. % • Set it up properly referring to “Speaker settings”. & Sound is not output from the surround speakers and / or the center speaker, or their sound is very small. • The surround speaker cords and/or the center speaker cord is disconnected. • The speaker is not set up correctly. •A surround mode has not been engaged. • The surround and/or center volume controls are set to the minimum level. • Connect it properly referring to “Connecting the speakers”. % • Set it up properly referring to “Speaker settings”. & • Select a surround mode. • Adjust the speaker levels using the test tone. * A humming noise is generated when the PHONO input selector is selected. • The audio cord from the record player is not connected to the PHONO jacks. • The record player is not grounded. • Insert the audio cord plugs securely into the PHONO jacks. • Connect the grounding wire to the GND terminal on the rear panel. When playing a Dolby Digital source signal using a DVD player, the sound is cut off soon after it starts. • There are many possible causes for this problem, depending on the type of DVD player used. • Set the input mode to digital manual before starting playback of the D...