Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
Familiarity with installation and operation procedures will help you obtain the best performance from your new cassette tuner equalizer. For your records Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your KENWOOD dealer for information or service on this product. Model KRC-999II Serial number_ When asking the service to KENWOOD dealer, be sure to send both the main unit and the control unit. ©PRINTED IN JAPAN B50-6914-00(K)(D 88/12 11 10 987654321 87/12 11 10 9 8 7 Controls and indicators Reset button When the installation and all the wirings are finished, press this button. Not usually used. However, when the microprocessor (microcomputer) malfunctions, press this button using a sharp-pointed object (such as a pencil). When this button is pressed, the unit is reset to its initial state. Therefore, all the memories and clock are erased and need to be adjusted. [TAPE]: Fast Forward/ Rewind switch Each switch permits Fast Forward or Rewind operation. To release the operation, press the Play/Program switch. [TUNER]: Tuning Up/Down switch Press the Up switch' to shift to a higher frequency. Press the Down switch to shift to a lower frequency. A single pressing of the switch allows the frequency to vary one step at a time. When the switch is kept pressed the frequency changes continuously. When the knob is moved once, the frequency is changed by 200 kHz in FM mode and 10 kHz in AM mode. [EQ]: Equalizer level Up/Down switch Press the Up switch to increase the equalizer level and the Down switch to decrease it. The equalizer level changes by one step when the switch is tapped once, and changes continuously when it is kept pressed. Cassette tape slot Insert the cassette tape into this slot with the cassette shell opening at the right until it reaches to the end of the slot. In this condition, tape will be automatically loaded when the Play/Program switch is pressed (this switch cannot be pressed when tuner is activated) or push the cassette further to engage manual loading. Volume indicator Indicates the present volume level. As the volume level increases, more indicator segments light, and m the same way, as volume level decreases, more indicator segments go off. J V [TAPE]: Play/Program switch If this switch is pressed during playback, the tape direction is reversed. If this switch is pressed during Fast Forward or Rewind mode, the Fast Forward or Rewind mode is released and the unit enters Play mode. [TUNER]: Band selector/indicators Selects reception band. Indicates the current receiv-•ing band. a FM1 FM2 FM3 AM [TAPE]: Operation and indication when the Tape switch is ON. [TUNER]: Operation and indication when the Tuner switch is ON. [EQ]: Operation and indication when the Equalizer switch is ON [TUNER]: Stereo reception indicator Lit when a stereo broadcast is received. Equalizer curve/Spec-trum analyzer display Displays the equalizer curve or the spectrum analyzer. db* / □□ DOLBY * C *110 FLECTION SELECTOR - ^2 £2 ^2 I 2 SSZ CSS 3 q Attenuator switch When this switch is set to ON, the volume indicator blinks and the volume instantaneously drops by — 20 dB When this switch is pressed again, the indicator goes off and the previous volume resumes. Auto volume switch When this switch is pressed ON after the optimum volume level is set, the volume will change automatically according to noise in the car. a c AT a c <*b. MTL H dbi MTL LO LO B6 CO LD y ON OFF [TAPE]: Tape remaining indicator Shows the remaining time of the tape, in 9-segment indicators. [TUNER]: Signal strength indicator The left four segments of the 9-segment indicators light according to the signal strength of the receiving broadcast station. Open/Close switch Press this switch to open the control drawer Pressing it again closes the drawer. With the drawer open, when the ignition key is turned OFF, the control drawer will be closed automatically. [TUNER]: Preset station switches (1—5) One switch can memorize one of each FM1, FM2, FM3 and AM. [EQ]: Equalizer curve preset switches (1—5) An equalizer -"curve can be preset for each switch. (En) 3 Controls and indicators [TUNER]: Manual/Auto switch This switch is used to select the tuning mode; Auto 1 (seek), Auto 2 (preset seek) or Manual. 5 - ¡er? ATa TAPE REMAIN _ ATI • 12 Auto 1 ATBj REMAIN Auto 2 _ AT1 ATZ TAPE REMAIN Manual [EQ]: Equalizer/Analyzer select switch This switch- is used to select the display mode; graphic equalizer curve display or spectrum analyzer display. [TAPE]: Clock display Displays the present time in the 12 hour system [TUNER]: Frequency/ Clock display Displays the frequency being received. The present time can also be displayed. [TAPE]: Tape running direction indicator Shows the running status of the tape. Audio control A (Up)/ V (Down...