Votos - 0, Puntuación media: 4 ( )

Fabricar: Transition Networks Tamaño del archivo: 78.88 kb Nombre del archivo: 8115786e-d7ad-d404-fd35-010e59d9e6dd.pdf Idioma del manual:

Power On SMACF10xx Units Install power adapter cord at back of each SMACF10xx unit. Connect power adapter power. Verify power by observing illuminated 3. Connect SMACF10xx Units to Ethernet ™ Network Locate path to Ethernet ™ segment. Use Category 5 twisted-pair cable and appropriate fiber cable to connect SMACF10xx Management through any port (optionally through a hub or switch) to the Ethernet ™ segment. Connect AT LEAST ONE port on EACH installed SMACF10xx Reporting Unit (optionally through a hub or switch) to the same Ethernet ™ segment. Main Management Unit Reporting Unit Network managed by SMACF10xx Management Unit. MM or SM Fiber In-Band Management VLAN Segmentation 10 or 100 Mb/s Speed Selection SNMP Management of Both Main Management and Reporting Units LAN Switch CAT 5 CAT 5 CAT 5 CAT 5 Corporate Technical Management Accounting Publications Remotely Managed Converters Manufacturing & Logistics SNMP Management of all Remote Reporting Units MM or SM Fiber Sales & Marketing PointSystem Modular Chassis Copper Switch Network managed by CPSMM-xxx PointSystem ™ Management Module connected to switch on same segment as Reporting Units. Configure Main Management Unit or Management Module Installed in Chassis NOTE: The SMAC10xx Management Unit contains both a Management Unit and a Reporting Unit. Each must be configured separately. 4. Connect Management Unit or Management Module to Terminal Locate null modem DB-9 serial port cable with female DB-9 connector. Attach DB-9 serial port female cable connector to DB-9 serial port male connector on SMACF10xx Management Unit OR on CPSMM-xxx PointSystem ™ Management Module installed in Media Conversion Center. Attach other end of DB-9 serial port cable to ASCII terminal or terminal emulator. 5. Verify Terminal Settings Default terminal settings are 9600 Baud/ 8 data bits/ 1 stop bit/ no parity. If necessary, use methods appropriate to terminal to modify settings. 6. Bring up Management Unit Interface at Terminal (SMACF10xx Management Unit ONLY) First set switch at back of SMACF10xx Management Unit to UP position. (SMACF10xx Management Unit and CPSMM-xxx PointSystem ™ Management Module) Press at terminal keyboard to bring up command-line prompt. 7. Enter superuser Mode At command-line prompt, type and enter the su command, using the case-sensitive Transition Networks default password private. CPSMM100> SU=private 2 8. Optionally Change To optionally passwords by changing superusercommand-line prompt, [SU] CPSMM100> public name> [SU] CPSMM100> SET private name> [SU] CPSMM100> SAVE 9. Set IP, Gateway, and Subnet Addresses At the superuser command-line prompt, type and enter addresses (in format: nnn.nnn.nnn.nnn) : [SU] CPSMM100> SET IP=< IP address> [SU] CPSMM100> SET NETMASK=< mask> [SU] CPSMM100> SET GATEWAY=< gateway address> [SU] CPSMM100> SAVE 10. Enter "secret word" At the superuser command-line prompt, type and enter: [SU] CPSMM100> SECRET= [SU] CPSMM100> SAVE Configure Reporting Unit(s) 11. Connect Reporting Unit to Terminal Refer to steps 4 and 5 for direction and terminal settings. 12. Bring up Reporting Unit Interface at Terminal (SMACF10xx Management Unit ONLY) First set switch at back of SMACF10xx Management Unit to DOWN position. (All SMACF10xx Reporting Units) Press at terminal to bring up Reporting Unit Main Menu. 13. Optionally Change CLI Login Password Pressing is the default Transition Networks Reporting Unit password. Optionally set an on-site Reporting Unit log-in password, using the command: p 14. Enter "secret word" Enter a secret word (identical to the secret word entered in the SMACF10xx Management Unit or the CPSMM-xxx PointSystem ™ Management Module) , using the command: c Repeat steps 11-14 for all installed SMACF10xx Reporting Units. 3 Manage SMACF10xx Units at Web Interface 15. Open Internet Browser Use browser versions 4.0, or Opera 4.0 and 16. Enter Management Unit At WWW location prompt, enter (in format: nnn.nnn.nnn.nnn) of the configured SMACF10xx or CPSMM-xxx PointSystem ™ Management Module. 17. Enter Password At the password prompt that comes up, the case-sensitive Transition Networks default password private(unless password was changed in step 8). A display showing available SMACF10xx units help available from the display for detailed direction the SMACF10xx units. © 2002 TRANSITION Networks. All rights reserved. No part of this work may be reproduced or used in any form or by any means – graphic, electronic, or mechanical – without written permission from TRANSITION Networks. Printed in the U.S.A. 33265. A 4 ...

Descargar ahora

Introduzca dos números de la imagen: