Votos - 2, Puntuación media: 3
(
)
)
|
Resumen del manual
Safety • Read the instructions in this manual carefully before you connect, install and use the product. • Keep this manual for future reference. • The product is for indoor use only. • Do not use the product close to water. • Do not expose the product to extreme heat. • In case of technical difficulties, do not open the product. Bring it to your Philips dealer. • Do not cover the product. • Connect the power adapters only to a 220-240 V AC/50 Hz power supply. • The product can cause interference to other equipment. Check if any equipment near the product can be affected before you start using it. EN EN Installation For basic installation, see the quick start guide that came with your Wireless TV Link. STANDBY SELECT SLV5400 WIRELESS TV LINK TRANSMITTER IR STANDBY SELECT SLV5400 WIRELESS TV LINK TRANSMITTER WIRELESS TV LINK RECEIVER Install the remote control blaster cord 1 Switch off the transmitter (A). 2 Connect the remote control blaster cord (G) to the IR port. 3 Position the blaster light in front of the video source. See the user manual of the video source for the exact location of the IR sensor on the front panel. 4 Switch on the transmitter (A). 5 Take the remote control of a video source with you. 6 Go to TV2. 7 Switch on TV2. 8 Switch on the receiver (B). 9 Select the correct SCART input on TV2. 10 Operate the video source with its remote control. 11 If necessary, repeat the steps 3 to 10 for the other video sources. Installation Installation EN L Channel DC 12V 1 2 3 4R CHANNEL 1 2 3 4 Remove interference on TV2 1 Find the CHANNEL switch on the transmitter (A). 2 Set the CHANNEL switch to different number. 3 Find the CHANNEL switch on the receiver (B). 4 Set the CHANNEL switch to the same number as on the transmitter. Operation Enjoy your Wireless TV Link For basic operation, see the quick start guide that came with your Wireless TV Link. Watch a cable TV program on TV2 1 Switch on the transmitter (A). 2 Switch on the VCR or DVD recorder. 3 Take the remote control of the VCR or DVD recorder with you. 4 Go to TV2. 5 Switch on TV2. 6 Switch on the receiver (B). Your VCR or DVD recorder needs to be connected to the transmitter (A) of the Wireless TV Link and connected to the Cable-TV signal. STANDBY SELECT SLV5400 WIRELESS TV LINK TRANSMITTER WIRELESS TV LINK RECEIVER OperationOperation EN 7 Press + or - on the receiver (B) to select the VCR or DVD recorder; or: press 4 on the remote control (C). 8 Select the channel on the VCR or DVD recorder with its remote control. Turn off the auto standby mode when you use the VCR or DVD recorder to watch a cable tv program. Refer to the user manual of the VCR or DVD recorder. If the VCR or DVD recorder records a television program, you watch the recorded channel. STANDBY SELECT SLV5400 WIRELESS TV LINK TRANSMITTER TV1 SOURCE Watch a video source on TV1 Either: automatic Operate TV1 and the video source as usual. Or: manual 1 Switch on the transmitter (A). 2 Switch on TV1. 3 Select the correct SCART input on TV1. 4 Select the video source with TV1 SOURCE; or: press + or - on the remote control (C). 5 Switch on the video source. 6 Operate the video source with its remote control. Operation Operation EN SELECT SAT/STB CONNECT 4-VCR/DVD RECORDER AUX DVD PLAYER 1 2 3 TV1 AUDIO OUT L R AudioAmplifierBe responsible Respect copyrights Use additional features Use VCR/DVD recorder features 1 Select a video source with SELECT. > The signal of the video source is connected to the VCR/DVD recorder. 2 Select the correct SCART input on the VCR or DVD recorder. 3 Push RECORD on the VCR or DVD recorder. 4 Push PLAY on the video source. > The VCR or DVD recorder now records the image of the video source. Sound through your audio amplifier 1 Take an audio cable (red and white plugs). 2 Plug the connectors of one end into the AUDIO OUT connectors on the transmitter (A). 3 Plug the connectors of the other end into the AUDIO IN connectors of your amplifier. The making of unauthorised copies of copy-protected material, including computer programmes, files, broadcasts and sound recordings, may be an infringement of copyrights and constitute a criminal offence. This equipment should not be used for such purposes. EN EN Troubleshooting Problem Tip No image or wrong image on TV1 • Make sure video sources are connected to the transmitter (A). • Make sure the transmitter (A) is connected to TV1. • Make sure SCART cables are firmly inserted. • Make sure the video source is switched on. • Make sure the correct SCART input on TV1 is selected. • Select the correct video source with TV1 source. See page 8. No image or wrong • Make sure SCART cables are image on TV2 firmly inserted. • Make sure the receiver (B) is connected to TV2. • Make sure both receiver (B) and transmitter (A) are switched on. • Make sure the video source is switched on. • Make sure the correct SCART input on TV2 is selected. • Select the correct video source with +/- on the receiver (B). • If the video source gives proper...
Otros modelos de este manual:Equipo de red - SLV5400/00 (322.32 kb)