Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
All rights reserved. Package Contents Configure DIP Switch • EIR102 Series Industrial Media Converter • Quick Start Guide (One per shipment) • Power Terminal Block (installed) • Fiber Optic Dust Covers (installed on fiber optic models) If any item is missing or damaged, contact B&B Electronics for a replacement 1. Fiber to Copper models have a 6 position switch. 2. Fiber to Fiber models have a 4 position switch. 3. Switches are numbered from the bottom. 4. Cycle power after changing DIP Switch configuration. 1 Power Terminal Block 2 Position, Removable 2 PWR LED ON When Power Applied 3 Fiber Optic SPD LED Normally OFF 3 Fiber Optic LINK LED On When Fiber Port Linked 4 Fiber Optic Ports No. & Type Depends on Model 5 RJ45 SPD LED ON if 100 mbps 5 RJ45 LINK LED ON When RJ45 Port Linked FLASHES When Data Transmitted 6 DIP Switch 4 POS for Fiber to Fiber 6 POS for Copper to Fiber 7 RJ45 Port Depends on Model Warning: Work Safe - Equipment damage or electrical shock hazard exists. DO NOT ATTACH OR REMOVE LEADS WITH THE POWER SUPPLY ENERGIZED! DIN Rail Mounting 1. Loosen the screw to open the terminal block lead clamp. 2. Insert the power lead. TB will accept 12-28 AWG wire. 3. Tighten the screw to close the terminal block lead clamp. Ensure the clamp holds the lead securely. However, do not over tighten. NOTE: For replacement Terminal Block order Part # 7444. 1. Slide and hold the DIN Clip toward the bottom of the Media Converter. Angle the top portion of the DIN mount over the top of the DIN rail. 2. Move the Media Converter so that it is parallel with the DIN Rail. 3. Release the DIN clip. The spring should return it to its original position. International Headquarters: 707 Dayton Road PO Box 1040 Ottawa, IL 61350 USA 815-433-5100 Fax 433-5104 support@bb-elec.com European Headquarters: Westlink Commercial Park Oranmore Co. Galway Ireland +353 91 792444 Fax +353 91 792445 support@bb-europe.com B&B ELECTRONICS QUICK START GUIDE 1. Auto MDI/MDI-x is supported. A straight through or cross-over cable may be used. 2. 10/100BaseT auto negotiation and full/halfduplex are supported. Speed and duplex can also be forced. Refer to DIP Switch settings. MDI Cable Pinout EIR102 1308qsg-2/2 © 2008 by B&B Electronics. All rights reserved. Attach RJ45 Cable Fiber Optic Cable (If equipped) Information Pin Signal 1 Tx+ 2 Tx- 3 Rx+ 6 Rx- MDI-X Cable Pinout Pin Signal 1 Rx+ 2 Rx- 3 Tx+ 6 Tx- Fiber Optic Cable information Mode and Distance Type Wa^ Multi-mode (2 km) 62.5/125 Mm 1310 nm Single-mode (15 km) 9/125 Mm 1310 nm Single-mode (40 km) 9/125 Mm 1310 nm Single-mode (80 km) 9/125 Mm 1550 nm Multi-mode (2 km) -19 to -14 dBm < -32 dBm Single-mode (15 km) -15 to -8 dBm < -32 dBm Single-mode (40 km) -5 to 0 dBm < -34 dBm Single-mode (80 km) -5 to 0 dBm < -34 dBm Installation Complete Attach Fiber Optic Cable 1. When the network cables are attached and power is applied, installation is complete. NOTE: Recycle power if DIP Switch changes are made after power up. A Warning: Work Safe - This is a Class I Laser/LED device. To avoid causing serious damage to your eyes, DO NOT STARE DIRECTLY INTO THE LIGHT. Ensure your fiber optic cable is terminated with the correct connector type. EIR102 Media Converters use SC or ST connectors. Fiber optic type for each port is located on the product’s side label. When connecting the cable to the media converter, be sure to line up the slider guide on the cable and media converter connectors. Connect the fiber optic transmitter to the downstream device’s receiver and vice-versa. Mechanical Diagram International Headquarters: 707 Dayton Road PO Box 1040 Ottawa, IL 61350 USA 815-433-5100 Fax 433-5104 support@bb-elec.com European Headquarters: Westlink Commercial Park Oranmore Co. Galway Ireland +353 91 792444 Fax +353 91 792445 support@bb-europe.com...