Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
• DO NOT INSTALL THE MONITOR IN A LOCATION WHICH OBSTRUCTS DRIVING AND VISIBILITY, OR WHERE APPLICABLE LAWS AND REGULATIONS PROHIBIT THE INSTALLATION. • NEVER USE BOLTS OR NUTS FROM THE VEHICLE’S SAFETY DEVICES FOR INSTALLATION. If bolts or nuts from the steering wheel, brakes, or other safety devices are used for installation, it may cause an accident. • CONNECT THE WIRES CORRECTLY. If the wiring is not correctly connected, it may cause a fire or an accident. In particular, be sure to run and secure the lead wire so that it does not get tangled with a screw or the moving portion of a seat rail. To prevent short circuits, it is recommended that you disconnect the battery’s negative terminal and make all electrical connections before installing the unit. If you are not sure how to install this unit correctly, have it installed by a qualified technician. • AVOID INSTALLING THE UNIT IN THE FOLLOWING PLACES: – Where it would hinder your safe driving. – Where it would be exposed to direct sunlight or heat directly from the heater, or placed in an extremely hot place. – Where it would be subject to rain, water splashes or excessive humidity. – Where it would be subject to dust. – Where it would be positioned in a unstable location. – Where it could damage the car’s fittings. – Where proper ventilation would not be maintained, such as under a floor mat. – Where it would be located near flammable objects (since heat is generated inside the unit). For safety.... Temperature inside the car.... • Do not raise the volume level too much, as If you have parked the car for a long time in this will block outside sounds, making driving hot or cold weather, wait until the temperature dangerous. in the car becomes normal before operating the • Stop the car before performing any unit. complicated operations. Controls and features KV-DT2000 functions together with the supplied remote controller—RM-RK520. How to reset your unit or (On the external (On the unit) remote sensor) This will reset the microcomputer. Your preset adjustments will also be erased. Installing the lithium coin battery (CR2025) Main elements and features ENGLISHWarning: • Do not install any battery other than CR2025 or its equivalent; otherwise, it may explode. • Store the battery in a place where children cannot reach to avoid risk of accident. • To prevent the battery from over-heating, cracking, or starting a fire: – Do not recharge, short, disassemble, heat the battery, or dispose of it in a fire. – Do not leave the battery with other metallic materials. – Do not poke the battery with tweezers or similar tools. – Wrap the battery with tape and insulate when throwing away or saving it. When operating, aim the remote controller directly at the remote sensor. Make sure there is no obstacle in between. • For connecting the remote sensor, refer to the Installation/connection manual (separate volume). 1 EPG (Electronic Program Guide) button* • Shows the TV program list sent by broadcast site. Press 5/./2/3 to scroll to the desired channel and program. 2 (standby/on) button • Turns the power on or off. Caution: To be continued.... ENGLISH 3 FAVOURITE button* • Shows the Favourite CH (CHannel) list (see Category grouping on page 10). Press 5/. to scroll to the desired channel, then press ENTER. • Resets to factory default setting if pressed and held while in the Main Menu screen. 4 INFO button • Shows the present/following program information, and clock. 5 ENTER button • While in setting mode, selects the highlighted function. • While in TV mode, displays the CH (CHannel) List. 6 2 (left) / 3 (right) buttons • While in setting mode: 3 (right): Scroll to the right. 2 (left): Scroll to the left. • While in TV mode, adjusts the volume level. 7 MENU button • Shows the main menu. Press 5/./2/3 to scroll to the desired submenu, then press ENTER. 8 MUTING button • Mutes the sound. 9 Number (0 – 9) buttons • Use for numeric entries, eg. program numbers, teletext page numbers, etc. p PROGRAM +/– buttons • While in TV mode, selects the TV programs. • While in radio mode, selects the radio programs. • While in teletext page, moves the teletext page up and down. q MULTILINGUAL button* • Selects the broadcast language if the selected program is broadcast in multi- language. Press 2/3 to scroll to the desired option, then press ENTER. w TV/RADIO button • Changes between the TV mode and radio mode. When radio mode is selected, only radio channels can be tuned in. e LIST button* • Selects the desired Service List (see page 11). Press 2/3 to scroll to the desired option, then press ENTER. r SOUND button • Select the appropriate sound system (AUTO, STEREO, MONO, Right-Both, Left-Both) for listening. Press SOUND repeatedly or 2/3 to scroll to the desired option, then press ENTER. t 5 (up) / . (down) buttons • While in setting mode, scrolls the selection menu up and down. • While in TV mode, selects the TV programs. • While in radio mode, selects the radio programs. • While in tele...