Votos - 1, Puntuación media: 3
(
)
)
|
Fotos y especificaciones Denon AVR-1404 |
Resumen del manual
(The included battery is only for verifying operation. Replace it with a new battery as soon as possible.) @ Insert the R6P/AA batteries properly, as e Close the lid. shown on the diagram. 15 ENGLISH 10 SETTING UP THE SYSTEM Once all connections with other AV components have been completed as described in "CONNECTIONS" (see pages 9 to 14), make the various settings described below on the display. These settings are required to set up the listening room's AV system centered around the this unit. 1 Set the slide switch to "AUDIO". C5~l • VIDEO — 2 • System setup items and default values (set upon shipment from the factory) System setup Default settings Speaker Configuration Input the combination of speakers in your system and their corresponding sizes (SMALL for regular speakers, LARGE for full-size, full-range) to automatically set the composition of the signals output from the speakers and the frequency response. Front Sp. Center Sp. Surround Sp. Sub Woofer Large Small Small Yes Subwoofer Mode This selects the subwoofer speaker for playing deep bass signals. Subwoofer mode = Normal Delay Time This parameter is for optimizing the timing with which the audio signals are produced from the speakers and subwoofer according to the listening position. Front & Subwoofer Center Surround L & R — 12 ft (3.6 m) 12 ft (3.6 m) 10 ft (3.0 m) — Digital In Assignment This assigns the digital input jacks for the different input sources. Digital Inputs COAXIAL OPTICAL Input source DVD/VDP TV/DBS NOTE: • The system setup is not displayed when "HEADPHONE ONLY" is selected. 16 ENGLISH Before setting up the system 1 ON/STANDBY Check that all the components are correct, then press the POWER operation switch on the main unit or on/source the POWER button on the remote control unit to turn on the power. (Main unit) (Remote control unit) 2 Press the SYSTEM SETUP button to enter the setting. NOTE: Please make sure the "AUDIO" position of the slide switch on the remote control unit. 3 Press the ENTER or (down) button to switch to the speaker configuration set up. NOTE: Press the SYSTEM SETUP button again to finish system set up. System set up can be finished at any time. The changes to the settings made up to that point are entered. Setting the speaker configuration 1 Use the 0 (left) and ^ (right) buttons to select your front speaker type. (Initial) e- -a (left) button (right) button Press the ENTER or (down) button to switch to the center speaker setting. 2 NOTE: Use the 0 (left) and (right) buttons to select your center speaker type. (Initial) e- -a (left) button (right) button Press the ENTER or (down) button to switch to the surround speaker setting. When "Small" has been selected for the front speakers, "Large" cannot be selected for the center speaker. 3 Use the ^ (left) and Q (right) buttons to select your surround speaker type. (Initial) e- -a (left) button (right) button Press the ENTER or (down) button to switch to the subwoofer setting. 17 ENGLISH NOTE: • When "Small" has been selected for the front speakers, "Large" cannot be selected for the surround speakers. Use the 0 (left) and 0 (right) buttons to select your subwoofer setting. (Initial) r yesi e- -a (left) button (right) button Press the ENTER or (down) button to enter the settings and switch to the SUBWOOFER MODE setting. • Parameters Large...... Select this when using speakers that can fully reproduce low sounds of below 80 Hz. Small...... Select this when using speakers that cannot reproduce low sounds of below 80 Hz with sufficient volume. When this setting is selected, low frequencies of below 80 Hz are assigned to the subwoofer. None...... Select this when no speakers are installed. Yes/No.... Select "Yes" when a subwoofer is installed, "No" when it's not installed. NOTE: Select "Large" or "Small" not according to the physical size of the speaker, but according to the bass reproduction capacity at 80 Hz. If you cannot determine the best setting, try comparing the sound when set to "Small" and when set to "Large", at a level that will not damage the speakers. Caution: In case the subwoofer is not used, be sure to set "Subwoofer = No", or the bass sound of front channel is divided to subwoofer channel and not reproduced in some mode. Setting the Subwoofer mode 1 Use the 0 (left) and 0 (right) buttons to select the Subwoofer mode. (Initial) 0- -o (left) button (right) button Press the ENTER or (down) button to enter the setting and switch to the Speaker Distance setting. NOTES: — Assignment of low frequency signal range — • The signals produced from the subwoofer channel are LFE signals (during playback of Dolby Digital or DTS signals) and the low frequency signal range of channels set to "SMALL" in the setup. The low frequency signal range of channels set to "LARGE" are produced from those channels. — Subwoofer mode — • The subwoofer mode setti...