Votos - 3, Puntuación media: 4.7
(
)
)
|
Fotos y especificaciones Denon AVR-1905 |
Resumen del manual
The “Auto tuner preset” operation can also be performed at “System setup”. (See page 30.) 1 1 2 DEFAULT VALUE 1 1 When the main unit’s power operation switch turn on while pressing the set’s PRESET • (+) button the unit automatically begins searching for FM broadcast stations. ON / STANDBY . PRESET • 2 2 When the first FM broadcast station is found, that station is stored in the preset memory at channel A1. Subsequent stations are automatically stored in order at preset channels A1 to A8, B1 to B8, C1 to C8, D1 to D8, E1 to E8, F1 to F8 and G1 to G8 for a maximum of 56 stations. 3 3 Channel A1 is tuned in after the auto preset memory operation is completed. NOTES: • If an FM station cannot be preset automatically due to poor reception, use the “Manual tuning” operation to tune in the station, then preset it using the manual “Preset memory” operation. •To interrupt this function, press the power operation button. AUTO TUNER PRESETS A1 ~ A8 87.5/89.1/98.1/107.9/90.1/90.1/90.1/90.1 MHz B1 ~ B8 520/600/1000/1400/1500/1710 kHz/90.1/90.1 MHz C1 ~ C8 90.1 MHz D1 ~ D8 90.1 MHz E1 ~ E8 90.1 MHz F1 ~ F8 90.1 MHz G1 ~ G8 90.1 MHz 58 Auto tuning ENGLISH ENGLISH 1 24 1 4 3 2 Set the input source to “TUNER”. Press the TUNING • (+) or . (–) button. 14 FUNCTION . TUNING • 2 2 (Main unit) (Remote control unit) Watching the display, press the BAND button to select the (Main unit) (Remote control unit) desired band (AM or FM). • Automatic searching begins, then stops when a station is tuned in. BAND NOTE: • When in the auto tuning mode on the FM band, the “STEREO” indicator lights on the display when a stereo broadcast is tuned in. (Main unit) (Remote control unit) At open frequencies, the noise is muted and the “TUNED” and “STEREO” indicators turn off. 3 3 Press the MODE button to set the auto tuning mode. Lit (Remote control unit) Manual tuning Set the input function to “TUNER”. Press the MODE button to set the manual tuning mode. Check that the display’s “AUTO” indicator turns off. 13 Watching the display, press the BAND button to select the Press the TUNING • (+) or . (–) button to tune in the desired desired band (AM or FM). station. 24 The frequency changes continuously when the button is held in. NOTE: • When the manual tuning mode is set, FM stereo broadcasts are received in monaural and the “STEREO” indicator turns off. 59 Preset stations ENGLISH ENGLISH Preparations: 23 Use the “Auto tuning” or “Manual tuning” operation to tune in the station to be preset in the memory. 1 1 Press the MEMORY button. (Remote control unit) 2 2 Press the SHIFT button and select the desired memory block (A to G). 3 SHIFT 2 1, 4 (Main unit) (Remote control unit) NOTE: Please make sure the “AUDIO” position of the slide switch on the remote control unit. 3 3 Press the PRESET • (+) or . (–) button to select the desired preset channel (1 to 8). . PRESET • (Main unit) (Remote control unit) 4 4 Press the MEMORY button again to store the station in the preset memory. (Remote control unit) To preset other channels, repeat steps 1 to 4. A total of 56 broadcast stations can be preset –8 stations (channels 1 to 8) in each of blocks A to G. Checking the preset stations •The preset (broadcast) stations can be checked on the on screen display. 1 1 Press the ON SCREEN/DISPLAY button repeatedly until the “Tuner Preset Stations” screen appears on the OSD. 1 (Remote control unit) 60 Recalling preset stations ENGLISH ENGLISH Watching the display, press the SHIFT button to select the 12 1 preset memory block. SHIFT (Main unit) (Remote control unit) NOTE: Please make sure the “AUDIO” position of the slide switch on the remote control unit. Watching the display, press the PRESET • (+) or . (–) button to select the desired preset channel. 2 2 1 1 . PRESET • (Main unit) (Remote control unit) 15 LAST FUNCTION MEMORY • This unit is equipped with a last function memory which stores the input and output setting conditions as they were immediately before the power is switched off. This function eliminates the need to perform complicated resettings when the power is switched on. • The unit is also equipped with a back-up memory. This function provides approximately one week of memory storage when the main unit’s power switch is off and with the power cord disconnected. 16 INITIALIZATION OF THE MICROPROCESSOR When the indication of the display is not normal or when the operation of the unit does not shows the reasonable result, the initialization of the microprocessor is required by the following procedure. 1 Switch off the unit using the main unit’s power switch. 2 Hold the following SPEAKER A button and B button, and turn the main unit’s power switch. 3 Check that the entire display is flashing with an interval of about 1 second, and release your fingers from the 2 buttons and the microprocessor will be initialized. 1, 2 2 NOTES: • If step 3 does not work, start over from step 1. • If the microprocessor has been reset, all the button settings are reset to the default...