Individual bands shall be activated by linear slide faders with a 25mm travel , and a tactile center detent. The range of equalization per band shall be either ±6dB or ±15dB selected via a 2-position switch. The equalizer shall have a gain of unity with all sliders centered, and shall have a maximum in/out level of +23dBu. Frequency response shall be ±.25dB 20Hz to 20kHz. Hum and noise shall be at least -92dBu and SMPTE intermodulation distortion or THD shall be less than .01% at full output. In

Each output permits you to set your crossover frequencies and may be assigned to any one or a combination of inputs. Additionally, you can program four filters (each of them your choice of parametric, low or high shelf), control delay for time delay adjustments, adjust output gain, reverse polarity and control a compressor/limiter for speaker protection. All this in one rack space with XLR input and output connections. Three Inputs - Six Outputs Extremely Intuitive User Interface Programmable b

Output Mute switches on each channel are included for convenient and accurate setup operation, and a peak overload indicator monitors all critical points in the circuit to ensure low-distortion operation. A recessed switch on the front panel with an LED indicator allows for either normal or "divide by ten" frequency selection. The XR Series II models feature Ashly's exclusive "Response" control, allowing the user to select the best performance for a given application. The purpose of this contro

.¡ t* EiiiiiliHil miiliUiUf liiiilS Si At Ashly, we believe that engineers should never have to compromise their standards for the sake of miniaturization. So we proudly offer the MQX Series equalizers, which feature all the performance and great sound of our legendary GQX models in uniquely compact packages. The MQX Series uses the same precision filter design and summing circuitry as the gQx Series, with each filter exhibiting true constant "Q" response. The center-detented position of each

The amplifier shall be an SRA-Series two-channel model, manufactured by Ashly Audio, Inc. of Rochester, New York. Features • 2RU Chassis • 4 Independent Channels • High Efficiency Switched Mode Power Supply • Class-D Output Circuitry • Input Attenuators On Rear Panel • Input Sensitivity 26dB or 36db • Remote Power Turn-On/Off • Adjustable Turn-on Delay • Convection Cooled • 6-Step Signal Level and Clip LEDs • Safety/Compliance: cTUVus/FCC, CE, RoHS TRA-Series Specifications 4075 41

The amplifiers shall have internally mounted transformers to provide both 70V and 100V constant voltage. Each channel shall deliver a minimum of 75W or 150W, model depending, to the constant voltage lines. Dimensions of the amplifiers shall be 19"W x 3.5"H x 11.0"D, with a weight of 29.5 pounds. The amplifiers shall utilize a state-of-the-art, efficient, switched mode power supply. The power supply shall operate at either 120 or 240VAC, 50/60Hz. The amplifier shall be convection cooled. The am

Frequency bands shall be activated by individual upand down tactile switches. The range of equalization per band shall be ±15dB in0.5dB increments. The equalizer shall have a gain of unity with all bands set at zero,and shall have a maximum in/out level of +20dBu. Frequency response shall be±.25dB 20Hz to20kHz. Dynamic Range shall be greater than 110dB (20-20KHz,unweighted) and SMPTE intermodulation distortion or THD shall be less than0.01% at 1KHz, +20dBu. Input impedance shall be 18K ohms bala

In general, large rooms benyou estimate the predominate feedback frequency efit from some low frequency shelf roll-off, high frequency to occur. shelf boost, and attenuation of ring mode frequencies by the parametric filters. 4. Push in the filter’s EQ switch and increase its level control by about +6 dB. Now “sweep” the 6.6 Small Room Equalization frequency around where you have estimated the feedback frequency until feedback occurs. Once Small rooms need less equalization than large you have i

Unless you have such an installation and have a hum problem you can’t solve by other means (ie: using balanced input and output connections), leave the ground jumper strap in place. 5. CONTROLS 5.1 Low Shelving Filter (Filter No. 1) 1. Low Shelf Level The nature of a shelving filter is such that the frequency response ramps up to a plateau and then levels off again, hence the term “shelf”. This level control knob adjusts the boost or cut of the signal below the tuned filter frequency as selected

In addition to the FTX amplifiers, input options can be installed on MFA High-Power amps, the CFT-1800 convection cooled amp, and P70 series 70 volt amps. A brief description of currently stocked input options follows. Consult your dealer for detailed information on input options, or call the factory at 800-828-6308. 8.1 Input Isolation Transformer (not shown) The input transformer provides complete electrical isolation from the amplifier and its signal source to eliminate any ground-induced hum