Votos - 2, Puntuación media: 3
(
)
)
|
Resumen del manual
001606 1 2 3 4 5 001606 1 2 3 4 5 1. Bolt 2. Drum 3. Planer blade 4. Drum cover 5. Adjust plate 001607 1 2 3 4 5 6 7 8 1. Adjust plate 2. Screws 3. Heel of adjust plate 4. Back side of gauge base 5. Blade edge 6. Planer blade 7. Inside edge of gauge plate 8. Gauge plate To install the blades, first clean out all chips or foreign matter adhering to the drum or blades. Use blades of the same dimensions and weight, or drum oscillation/vibration will result, causing poor planing action and, eventually, tool breakdown. Place the blade on the gauge base so that the blade edge is perfectly flush with the inside edge of the gauge plate. Place the adjust plate on the blade, then simply press in the heel of the adjust plate flush with the back side of the gauge base and tighten two screws on the adjust plate. Now slip the heel of the adjust plate into the drum groove, then fit the drum cover on it. Tighten the installation bolts evenly and alternately with the socket wrench. For the correct planer blade setting For the correct planer blade setting s the blade is set properly and securely. The blade must be mounted so that the cutting edge is absolutely level, that is, parallel to the surface of the rear base. Below are some examples of proper and improper settings. EN0004-1 (A) Front base (Movable shoe) (B) Rear base (Stationary shoe) Correct setting Nicks in surface Gouging at start Gouging at end (A) (B) (B) (A) (B) (A) Although this side view cannot show it, the edges of the blades run perfectly parallel to the rear base surface. Cause: One or both blades fails to have edge parallel to rear base line. Cause: One or both blade edges fails to protrude enough in relation to rear base line. Cause: One or both blade edges protrudes too far in relation to rear base line. OPERATION 001608 Planing operation First, rest the tool front base flat upon the workpiece surface without the blades making any contact. Switch on and wait until the blades attain full speed. Then move the tool gently forward. Apply pressure on the front of tool at the start of planing, and at the back at the end of planing. Planing will be easier if you incline the workpiece in stationary fashion, so that you can plane somewhat downhill. The speed and depth of cut determine the kind of finish. The power planer keeps cutting at a speed that will not result in jamming by chips. For rough cutting, the depth of cut can be increased, while for a good finish you should reduce the depth of cut and advance the tool more slowly. 2 1 1. Start 2. End 001609 001609 Chamfering To make a cut as shown in the figure, align the “V’’ groove in the front base with the edge of the workpiece and plane it as shown in the figure. 001613 1 2 1. “V” groove 2. Front base 001614 1. Align the (Y) groove with the edge of the workpiece MAINTENANCE CAUTION: • Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. 001610 Sharpening the planer blades Always keep your blades sharp for the best performance possible. Use the sharpening holder to remove nicks and produce a fine edge. 1 1. Sharpening holder 1 4 2 3 1 4 2 3 Wing nut 2. Blade(A) 3. Blade(B) 4. Side(C) 5. Side(D) 001611 First, loosen the two wing nuts on the holder and insert the blades (A) and (B), so that they contact the sides (C) and (D). Then tighten the wing nuts. 5 001612 Immerse the dressing stone in water for 2 or 3 minutes before sharpening. Hold the holder so that the blades both contact the dressing stone for simultaneous sharpening at the same angle. To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection and replacement, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. ACCESSORIES ACCESSORIES CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita service center. • 110 mm (4-3/8”) Planer blade • Dressing stone • Sharpening holder assembly • Blade gauge • Guide rule • Extension guide set • Socket wrench 9 • Dust bag Memo Memo Cut Cut s Postage Required Post Office will not deliver without proper postage. Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 Fold MAIL THIS PORTION Your answers to the following questions are appreciated. 1. This product was purchased from: Home Center Other ( Hardware/Lumber Store Tool Distributor Industrial Supply Construction Supply 2. Use of the product is intended for: Construction Trade Industrial Maintenance Home Maintenance Hobby Other ( ) 5. Any comments: 3. How did you learn about this product: ) Magazine Radio From Dealer Exhibition Newspaper From Friend Store Display Previous Usage Catalo...