Votos - 7, Puntuación media: 4.3
(
)
)
|
Fotos y especificaciones Makita 1806B |
Resumen del manual
should never be left around the work area. 7. Before using the tool on an actual work2. Avoid cutting nails. Inspect for and piece, let it run for a while. Watch for remove all nails from the workpiece before vibration or wobbling that could indicate operation. poor installation or a poorly balanced blade. 3. Use only sharp blades. Handle the blades very carefully. 8. Make sure the blade is not contacting the workpiece before the switch is turned on. 4. Be sure the blade installation bolts are securely tightened before operation. 9. Wait until the blade attains full speed before cutting. 5. Hold the tool firmly with both hands. 10. Keep at least 200 mm (8”) away from the tool at all times. 11. Always switch off and wait for the blades to come to a complete stop before any adjusting. 12. Never stick your finger into the chip chute. Chute may jam when cutting damp wood. Clean out chips with a stick. 13. Do not leave the tool running. Operate the tool only when hand-held. 14. When leaving the planer, switch off and set it with the front base up on a wooden block, so that the blades do not contact anything. 15. Always change both blades or covers on the drum, otherwise the resulting imbalance will cause vibration and shorten tool life. 16. Wait for complete run-down before putting the tool aside. 17. Use only Makita blades specified in this manual. 18. Some material contains chemicals which may be toxic. Take caution to prevent dust inhalation and skin contact. Follow material supplier safety data. SAVE THESE INSTRUCTIONS WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. SYMBOLS USD201-2 The followings show the symbols used for tool. V .......................volts n....................no load speed ° A ....................... amperes ....................Class II Construction Hz ..................... hertz .../min................revolutions or reciprocation per minute ................ alternating current FUNCTIONAL DESCRIPTION FUNCTIONAL DESCRIPTION 1 1. Knob 002552 1 2 1. Lock button 2. Switch trigger CAUTION: • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Adjusting depth of cut Depth of cut may be adjusted by simply turning the knob on the front of the tool. Switch action CAUTION: • Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released. • Switch can be locked in “ON” position for ease of operator comfort during extended use. Apply caution when locking tool in “ON” position and maintain firm grasp on tool. To start the tool, simply pull the switch trigger. Release the switch trigger to stop. For continuous operation, pull the switch trigger and then push in the lock button. To stop the tool from the locked position, pull the switch trigger fully, then release it. ASSEMBLY ASSEMBLY CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. 002560 Removing or installing planer blades CAUTION: • Tighten the blade installation bolts carefully when attaching the blades to the tool. A loose installation bolt can be dangerous. Always check to see they are tightened securely. • Handle the blades very carefully. Use gloves or rags to protect your fingers or hands when removing or installing 1 2 1. Hex wrench 2. Bolt the blades. • Use only the Makita wrench provided to remove or install the blades. Failure to do so may result in overtightening or insufficient tightening of the installation bolts. This could cause an injury. To remove the blades on the drum, unscrew the five installation bolts with the hex wrench. The drum cover comes off together with the blades. 002561 To install the blades, first clean out all chips or foreign matter 1 2 3 adhering to the drum or blades. Use blades of the same dimensions and weight, or drum oscillation/vibration will result, causing poor planing action and, eventually, tool breakdown. 4 There are two adjusting screws for each blade. When install5 ing the blade, the notch in the blade should fit over the head 1. Adjusting screw 2. Planer blade of the adjusting screw. Then fit on the drum cover and secure all the installation bolts only finger-tight. 3. Notch in the blade 4. Drum cover 5. Drum Turn the drum until the blade edge is right in the middle between the front and rear bases. 002562 Place the triangular rule flat on the rear base and run it out 1 2 1. Triangular rule 2. Screwdriver over and across the blade edge. Turn the two adjusting screws to adjust the blade protrusion. The blade setting should be made so that the protrusion will be uniform all the way across. Thus the triangular rule should be flush with the entire width of the blade edge. After adjusting both blades, tighten all the installation bolts evenly and alternately with the wrench. After tightening the bolts, secure the adjusting screws fully. ...