Votos - 4, Puntuación media: 3.8
(
)
)
|
Resumen del manual
Roller spring tension adjustment cap screws. G0453/G0454 (Mfg. Since 3/08) Figure 49. Chip deflector and securing hex bolts. * -43- 4. If the distance measured in Step 3 is not equal to W, then loosen the four hex bolts that secure the chip deflector and adjust the gap to W. 5. Re-tighten the hex bolts, then replace the belt cover, top cover, and dust hood. Scale Calibration Although correctly set at the factory, the scale can be adjusted for accuracy if it becomes necessary. Tools Needed Qty Phillips Screwdriver #2......................................1 Scrap Piece of Stock.........................................1 Calipers.............................................................1 To re-position the scale: 1. Plane the scrap piece of stock until it is flat and of even thickness along its length. Note: pass. Turn the board over between each 2. Use calipers to measure the board thickness. 3. If there is a discrepancy between the board thickness and the reading on the table height scale, loosen the two screws shown in Figure 50, adjust the scale in relation to the pointer, then re-tighten the screws. Figure 50. Table height scale. -44- Anti-Kickback Fingers The anti-kickback fingers are an important safety feature of your planer. The fingers hang from a rod suspended across the head casting and in front of the infeed roller, as shown in Figure 51. This design allows the workpiece to easily enter the planer but reduces the risk of kickback by digging into the workpiece if it moves backward. t- Anti-Kickback Fingers o I Or Figure 51. Anti-kickback fingers. Check the anti-kickback fingers regularly to ensure they swing freely and easily. If the fingers do not swing freely and easily, first clean them with a wood resin solvent, then inspect them for damage. If any of the fingers are damaged, the device must be replaced before using the machine. Do not apply oil or other lubricants to the antikickback fingers that will attract dust, and restrict the free movement of the fingers. ▲warning Proper operation of the anti-kickback fingers is critical for the safe operation of this planer. DO NOT operate the planer if the anti-kickback fingers are not operating correctly. Failure to heed this warning could result in serious personal injury. G0453/G0454 (Mfg. Since 3/08) Pulley Alignment Proper pulley alignment prevents premature V-belt wear and unnecessary load on the motor. The pulleys are properly aligned when they are parallel and in the same plane as each other. Tools Needed Qty Straightedge 3'..................................................1 Hex Wrench 6mm..............................................1 Wrenches or Sockets 14mm.............................1 To check/re-align pulleys: 1. DISCONNECT PLANER FROM POWER! 2. Remove both cabinet covers and the belt cover, then use the straightedge to check pulley alignment, as shown in Figure 52. Figure 52. Checking pulley alignment. —If the pulleys are not in the same plane, loosen the cap screw or hex bolt securing the pulley to the shaft, then adjust the pulleys in or out until they are aligned. —If the pulleys are not parallel, loosen the four motor mount hex nuts, then rotate the motor on its mount until the pulleys are parallel. 3. Re-check the pulleys and repeat Step 2 if necessary. 4. When your are satisfied with the pulley alignment, re-tighten all fasteners, then replace the belt cover and cabinet covers. G0453/G0454 (Mfg. Since 3/08) -45- SECTION S: WIRING These pages are current at the time of printing. However, in the spirit of improvement, we may make changes to the electrical systems of future machines. Compare the manufacture date of your machine to the one stated in this manual, and study this section carefully. If there are differences between your machine and what is shown in this section, call Technical Support at (570) 546-9663 for assistance BEFORE making any changes to the wiring on your machine. An updated wiring diagram may be available. Note: Please gather the serial number and manufacture date of yout machine before calling. This information can be found on the main machine label. ▲WARNING Wiring Safety Instructions SHOCK HAZARD. Working on wiring that is connected to a power source is extremely dangerous. Touching electrified parts will result in personal injury including but not limited to severe burns, electrocution, or death. Disconnect the power from the machine before servicing electrical components! MODIFICATIONS. Modifying the wiring beyond what is shown in the diagram may lead to unpredictable results, including serious injury or fire. This includes the installation of unapproved aftermarket parts. WIRE CONNECTIONS. All connections must be tight to prevent wires from loosening during machine operation. Double-check all wires disconnected or connected during any wiring task to ensure tight connections. CIRCUIT REQUIREMENTS. You MUST follow the requirements at the beginning of t...
Otros modelos de este manual:Aviones - G0453 (3.78 mb)