Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
Knead the plastic bag to distribute the oil. Squeeze the excess oil out of the filter inside the plastic bag and pour off the excess before fitting the filter to the machine. Never use common engine oil. This would drain through the filter quite quickly and collect in the bottom. An air filter that has been in use for a long time cannot be cleaned completely.The filter must therefore be replaced with a new one at regular intervals. A damaged air filter must always be replaced. Bevel gear The bevel gear is filled with the right quantity of grease at the factory. However, before using the machine you should check that the bevel gear is filled three-quarters full with grease. Use HUSQVARNA special grease. The grease in the bevel gear does not normally need to be changed except if repairs are carried out. Spark plug The spark plug condition is influenced by: • Incorrect carburettor adjustment. • An incorrect fuel mixture (too much or incorrect type of oil). • A dirty air filter. These factors cause deposits on the spark plug electrodes, which may result in operating problems and starting difficulties. If the machine is low on power, difficult to start or runs poorly at idle speed: always check the spark plug first before taking any further action. If the spark plug is dirty, clean it and check that the electrode gap is 0,6-0,7 mm. The spark plug should be replaced after about a month in operation or earlier if necessary. CAUTION! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/cylinder. Check that the spark plug is fitted with a suppressor. English – 23 MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this Operator’s Manual. More extensive work must be carried out by an authorised service workshop. Maintenance Daily maintenance Weekly maintenance Monthly maintenance Clean the outside of the machine. X Check that the harness is not damaged. X Make sure the throttle trigger lock and the throttle function correctly from a safety point of view. X Check that the handle and handlebar are undamaged and secured correctly. X Check that the stop switch works correctly. X Check that the cutting attachment does not rotate at idle. X Clean the air filter. Replace if necessary. X Check that the guard is undamaged and not cracked. Replace the guard if it has been exposed to impact or is cracked. X Check that the blade is correctly centred, is sharp, and is not cracked. An off-centre blade will cause vibration that could result in damage to the machine. X Check that the trimmer head is undamaged and not cracked. Replace the trimmer head if necessary. X Check that the locking nut of the cutting equipment is tighten correctly. X Check that the transport guard for the blade is intact and that it can be secured correctly. X Check that nuts and screws are tight. X Check that there are no fuel leaks from the engine, tank or fuel lines. X Check the starter and starter cord. X Check that the vibration damping elements are not damaged. X Clean the outside of the spark plug. Remove it and check the electrode gap. Adjust the gap to 0.5 mm or replace the spark plug. Check that the spark plug is fitted with a suppressor. X Clean the machines cooling system. X Clean or replace the spark arrestor mesh on the muffler (only applies to mufflers without a catalytic converter). X Clean the outside of the carburettor and the space around it. X Check that the bevel gear is filled three-quarters full with lubricant. Fill if necessary using special grease. X Check the fuel filter from contamination and the fuel hose from cracks or other defects. Replace if necessary. X Check all cables and connections. X Check the clutch, clutch springs and the clutch drum for wear. Replace if necessary by an autorized service workshop. X Replace the spark plug. Check that the spark plug is fitted with a suppressor. X Check and clean the spark arrestor mesh on the muffler (only applies to mufflers fitted with a catalytic converter). X 24 – English TECHNICAL DATA Technical data Technical data Engine Cylinder displacement, cm3 Cylinder bore, mm Stroke, mm Idle speed, rpm Recommended max. fast idle speed, rpm Speed of output shaft, rpm Max. engine output, acc. to ISO 8893, kW/ rpm Catalytic converter muffler Speed-regulated ignition system Spark arrestor mesh Ignition system Manufacturer/type of ignition system Spark plug Electrode gap, mm Fuel and lubrication system Manufacturer/type of carburettor Fuel tank capacity, litre Weight Weight without fuel, cutting attachment and guard, kg Noise emissions (see note 1) Sound power level, measured dB(A) Sound power level, guaranteed LWA dB(A) Noise levels (see note 2) Equivalent sound pressure level at the operator's ear, measured according to EN ISO 22868, dB(A), min./max.: Vibration...