Votos - 6, Puntuación media: 4
(
)
)
|
Resumen del manual
Stay off steep slopes! • Follow maintenance and lubrication instructions as outlined in this manual. LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAUTIONS. IT MEANS -- ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED. CARTON CONTENTS LOOSE PARTS IN CARTON 1.Hitch Tube 2.Flow Control Arm 3.Hitch Bracket 4.Flow Control Mount Bracket 5.Braces (2) 6.Flow Control Rod 7.Wheels (Drive and Idler) 8.Hopper Assembly Hardware Package (see page 3) 1 5 6 74 8 2 3 2 E F DCBA K L G M N O P Q R NOT SHOWN FULL SIZE SHOWN FULL SIZE H J I S E F DCBA K L G M N O P Q R NOT SHOWN FULL SIZE SHOWN FULL SIZE H J I S KEY QTY. DESCRIPTION KEY QTY. DESCRIPTION A B C D E F G H I 5 2 2 1 9 2 4 8 3 Hex Bolt, 1/4-20 x 1-1/2" Hex Bolt, 1/4-20 x 1" Hex Bolt, 1/4-20 x 3/4" Carriage Bolt, 1/4-20 x 3/4" Hex Lock Nuts, 1/4-20 Thread Lock Washer, 1/4" I.D. Nylon Washer Flat Washer, 5/16" Flat Washers 1/2" J K L M N O P Q R S 1 1 1 1 2 1 1 1 1 2 Cotter Pin, 3/32" x 3/4" Cotter Pin, 5/32 x 2" Hair Cotter Pin, 1/8" Hitch Pin Spacers Nylon Wing Nut Adjustable Stop Flow Control Link Grip Hub Cap 3 6.Align the holes in the ends of the two hitch braces ASSEMBLY INSTRUCTIONS with the nearest hole in the hitch tube. Fasten with a 1/4" x 1-1/2" hex bolt and a 1/4" hex lock nut. See figure 2. Do not tighten at this time. TOOLS REQUIRED FOR ASSEMBLY (1) Pliers (2) 7/16" Open or Box End Wrenches (2) 1/2" Open or Box End Wrenches (1) Small Hammer 1.Remove the spreader, loose parts and hardware package from the carton. Lay out all parts and hardware and identify using the illustrations on pages 2 and 3. 2.Turn the spreader upside down as shown in figure 1, so that it rests on the hopper. 3.Remove the 1/4" hex bolt, flat washer and hex lock nut from the center of the crossover tube and shaft support plate. See figure 1. FIGURE 2 7.Tighten all hex nuts and bolts, following the same sequence as assembled in steps 4, 5 and 6. Do not collapse tube when tightening. 8.Assemble a spacer and then a 1/2" flat washer onto each end of the axle. See figure 3. 1/4" HEX LOCK NUT 1/4" FLAT WASHER 1/4" x 1-1/2" HEX BOLT 1/4" HEX LOCK NUT 1/4" x 1-1/2" HEX BOLT CROSSOVER TUBE HITCH BRACES HITCH TUBE HOPPER FRAME SHAFT SUPPORT PLATE FIGURE 1 4.Assemble the two hitch braces to the inside of the hopper frame, one on each side, using two 1/4" x 1-1/2" hex bolts and two 1/4" hex lock nuts. See figure 2. Do not tighten at this time. 5.Assemble short end of hitch tube to the crossover tube (on opposite side from shaft support plate). Fasten to the center hole in the crossover tube using the 1/4" x 1-1/2" hex bolt, the 1/4" flat washer and the 1/4" hex lock nut removed in step 3. See figures 1 and 2. Do not tighten at this FIGURE 3 AXLE SPACER 1/2" DIA. FLAT WASHER time. 4 9.Place a wheel (long end of hub first) onto the end of the axle that has no cross hole. See figure 4. 10.Place a 1/2" flat washer onto the axle and then lightly tap a hub cap onto the axle until it is snug against the washer and wheel hub. See figure 4. 1/2" FLAT WASHER HUB CAP END WITH NO CROSS HOLE FIGURE 4 11.Place a wheel onto the end of the axle that has a cross hole. The long end of the hub goes to the inside. See figure 5. 12.Assemble a 5/32" x 2" cotter pin through the notched wheel hub and the axle. See figure 5. 13.Place a hub cap onto the end of the axle.Using a small hammer, lightly tap the hub cap until it is snug against the wheel. See figure 5. 5/32" x 2" COTTER PIN HUB CAP CROSS HOLE 14.In order to assemble the hitch bracket to the hitch tube, turn the spreader upright on its wheels. Assemble the bracket to the top of the hitch using two 1/4" x 1" hex bolts, 1/4" lock washers and 1/4" hex lock nuts. See figure 6. FIGURE 6 1/4" x 1" HEX BOLT 1/4" LOCK WASHER 1/4" HEX LOCK NUT HITCH PIN HAIR COTTER PIN 15.Assemble the flow control link (end with small hole) to the flow control arm using a 1/4" x 3/4" hex bolt, a nylon washer and a 1/4" hex lock nut as shown in figure 7. Tighten carefully. The flow control link should not be loose but should pivot with no more than slight resistance. FLOW CONTROL LINK 1/4" x 3/4" HEX BOLT SMALLEST HOLE NYLON WASHER FLOW CONTROL ARM 1/4" HEX LOCK NUT FIGURE 7 FIGURE 5 5 16.Assemble the flow control arm to the flow control mounting bracket using a 1/4" x 3/4" hex bolt, two nylon washers and a 1/4" hex lock nut as shown in figure 8. Tighten carefully. The flow control arm should be snug, but should pivot with no more than a slight resistance. 17.Assemble the vinyl grip. See figure 8. 1/4" x 3/4" HEX BOLT FLOW CONTROL MOUNTING BRACKET FLOW CONTROL ARM VYNIL GRIP 1/4" HEX LOCK NUT (2) NYLON WASHERS FIGURE 8 18.Place a 5/16" flat washer onto the end of the flow control rod. Insert the end of the rod through the slot in the flow control mounting bracket and through the hole in the flow control link. Secure with a 3/32" x 3/4" cotter pin. See figure 9. FLOW CONTROL ROD FLOW CONTROL LINK 3/32" COTTER PIN 5/16" FLAT WASHER SLOT 19.Hook the free end of the flow control ro...