Votos - 4, Puntuación media: 3.8
(
)
)
|
Resumen del manual
The faster you drive, the wider the broadcast width. Always start the tractor in motion before opening closure 6. plate. Always shut the closure plate before turning or stopping 7. the tractor. If fertilizer is accidentally deposited too heavily in a small 8. area, soak the area thoroughly with a garden hose or sprinkler to prevent burning of the lawn. To insure uniform coverage, make each pass so that the 9. broadcast pattern slightly overlaps the pattern from the previous pass as shown in figure 8. The approximate broadcast widths for different materials are shown in the application chart on this page. When broadcasting weed control fertilizers, make sure 10. the broadcast pattern does not hit evergreen trees, flowers or shrubs. Heavy moisture conditions may require a cover over 11. the hopper to keep contents dry. The vinyl cover acts as a wind and moisture shield, but should not be used as a rain cover. FIGURE 7 OVERLAPREFER TOCHARTS GREASEOILOIL FIGURE 8 IMPORTANT: Application rates shown in the chart are affected by humidity and by the moisture content of the material (granular and pellet). Some minor setting adjustments may be necessary to compensate for this condition. FIGURE 9 APPLICATION CHART (SHIELD UP) TYPE SPREAD MATERIAL FLOW SETTING WIDTH FERTILIZER Powder 3 - 5 3' - 4' Granular 3 - 5 8' - 10' Pelleted 3 - 5 10' - 12' Organic 6 - 8 6' - 8' GRASS SEED Fine 3 - 4 6' - 7' Coarse 4 - 5 8' - 9' ICE MELTER 6 - 8 10' - 12' STORAGE 1. Rinse inside of hopper and exterior of spreader and dry off before storing. 2. Store in a clean, dry area. SERVICE AND ADJUSTMENTS 1. If the axle, slotted gear and sprocket assembly is disassembled, mark down the positions of the parts as they are removed. The drive wheel and sprocket positions in relation to the slotted gear determine which direction the spreader plate will spin. Be sure to reassemble them in their original positions. (Refer to figure 5 on page 3.) Use shim washers (Ref. no. 21 on pages 6 and 7) as needed for minimum backlash. Add grease to gear and sprocket. 2. If the agitator hairpin becomes damaged or worn it can be replaced. See figure 10. OPERATING SPEED - 3 MPH. (100 ft. in 23 seconds) MAINTENANCE CHECK FOR LOOSE FASTENERS 1. Before each use make a thorough visual check of the spreader for any bolts and nuts which may have loosened. Retighten any loose bolts and nuts. CHECK FOR WORN OF DAMAGED PARTS 2. Check for worn or damaged parts before each use. Repair or replace parts if necessary. CHECK TIRE INFLATION 3. Check if tires are adequately inflated before each use. Do not inflate beyond maximum recommended pressure. CLEANING 4. Rinse inside of hopper and exterior of spreader and dry off before storing. LUBRICATE (See figure 9.) 5. Lightly apply automotive grease as needed to the sprocket and gear. 6. Oil the nylon bushings on the vertical sprocket shaft and on the axle at least once a year, or more often as needed. 7. Oil right hand (idler) wheel bearing at least once a year or more often as needed. SPROCKETSHAFTAGITATOR HAIRPIN CAUTION: DO NOT inflate tires beyond the maximum recommended pressure printed on side of tire. FIGURE 10 REPAIR PARTS FOR BROADCAST SPREADER MODEL 45-02153-131 11242343222120212219184DE3522161123AA11227262831936349469139401514911171124229E9313354935B6712409D3350401225B139501039932944487 7842453273841323739932394751324049 REPAIR PARTS FOR BROADCAST SPREADER MODEL 45-02153-131 REF PART NO. QTY DESCRIPTION 1 44624 1 Hopper 2 46055 1 Pin, Spring 1/8" Dia. x 1" Lg. 3 62482 1 Ass'y, Guide Closure 4 40469 1 Tube, Frame 5 23753 1 Slide Gate Angle Bracket 6 23758 1 Slide Gate Bracket 7 43661 5 Bolt, Hex 1/4-20 x 1" Lg.* 8 24857 1 Flow Control Link 9 47189 22 Nylock Nut, 1/4-20 10 44591 1 Tube, Crossover 11 43648 9 Bolt, Hex 1/4-20 x 1-1/2" Lg. 12 1509-69 7 Bolt, Hex 1/4-20 x 1-3/4" 13 44566 1 Spring, Torsion 14 44586 1 Tube, Hitch 15 40539 1 Drive Wheel 16 40540 1 Wheel 17 23687 1 Bracket, Hitch 18 23781 1 Shaft, Axle 19 44665 2 Pin, Spring 5/32" Dia. x 1-1/4" Lg. 20 44672 1 Bushing, Axle Shaft 21 44137 6 Washer, Shim 1/2" 22 R19171616 4 Washer, Flat 1/2" 23 47963 2 Bearing, Flange 24 46501 2 Tube, Spacer 25 25305 1 Shaft, Sprocket 26 04367 1 Spreader Plate REF PART NO. QTY DESCRIPTION 27 43850 1 Pin, Spring 1/8" Dia. x 5/8" Lg. 28 44468 1 Sprocket, 6 Tooth 29 C-9M5732 2 Pop Rivet (not shown) 31 48934 1 Hairpin Agitator 32 R19111116 9 Washer, 5/16 SAE 33 44285 2 Bushing, Delrin 34 44469 1 Rod, Flow Control 35 23525 2 Brace, Hitch 36 23780 1 Support, Shaft 37 47141 1 Nylon Wing Nut, 1/4-20 Thd. 38 44950 1 Bolt, Carriage 1/4-20 x 3/4" Lg. 39 1543-69 10 Washer, Nylon 40 43088 16 Washer, Flat 1/4" Std. 41 24858 1 Adjustable Stop 42 24855 1 Bracket, Flow Control Mount 43 46885 1 Gear 44 24859 1 Flow Control Arm 45 44101 1 Cotter Pin 3/32" x 3/4" Lg.* 46 23533 1 Plate, Closure 47 47623 1 Hitch Pin 48 43848 1 Grip, Flow Control Arm 49 40883 1 Vinyl Hopper Cover 50 44663 2 Hub Cap 51 43343 1 Hair Cotter Pin, #4 1/8" 40537 1 Owner's Manu...