Fabricar: Agri-Fab
Tamaño del archivo: 1.2 mb
Nombre del archivo: 45-03011.pdf
![en en](/images/flag/s/en.gif)
![]() |
Resumen del manual
Attach the hopper brace to the top of the tongue and the hitch bracket to the bottom using one 3/8" x 1" hex bolt, 3/8" lock washer and 3/8" hex lock nut. Do not tighten yet. See figure 4. FIGURE 2 5. Assemble the plastic grip onto the end of the flow control arm as shown in figure 3. 6. Insert the flow control arm through the slot in the hopper brace. Place a nylon washer on each side of the arm and attach it to the brace's welded bracket using a 1/4" x 1-1/4" hex bolt, a 1/4" flat washer and two 1/4" hex lock nuts as shown in figure 3. Tighten the first hex lock nut until there is noticeable resistance when moving the flow control arm, then tighten the second hex lock nut. 7. Place the flow control rod through the hole at the end of the flow control arm. Assemble the two ferrules onto the threaded ends of the rod so that approximately 10 threads (1/2") of the rod extends through the ferrules. See figure 3. 3/8" HEXNYLOCK NUT1/4" x 5/8" HEX BOLT3/8" x 1" HEX BOLT1/4" FLATWASHER(ONE ONLY) 1/4" HEX NUTHOPPERBRACEHITCHBRACKET FIGURE 4 1/4" NYLOCK NUTBRACKETFERRULE NOTE: The wheels may be temporarily removed for easier access when assembling the tongue braces in the following instructions. 10. Insert a tongue brace through the slot in the end plate. Fasten the front hole of the tongue brace to the end plate using a 1/4" x 5/8" hex bolt and 1/4" hex nut. For the rear hole use a 1/4" x 3/4" hex bolt, 1/4" flat washer and 1/4" hex nut, with the bolt and washer assembled from inside the poly hopper. See figure 5. Do not tighten yet. 11. Fasten the other end of the tongue brace to the side of the tongue using two 1/4" x 5/8" hex bolts and 1/4" hex nuts. Do not tighten yet. See figure 5. 12. Repeat steps 10 and 11 for the second tongue brace. 13. Tighten all bolts and nuts assembled so far. 15. Check that both ferrules are adjusted so that approximately ten threads (1/2") of the control rod is exposed. Insert both ferrules into the brackets which are riveted to the front of the flow plates. Assemble a 1/4" hex lock nut onto each ferrule, making only finger tight at this time. See figure 7. 1/4" x 5/8" HEX BOLT1/4" NYLOCK NUT1/4" x 5/8" HEX BOLT1/4" NYLOCK NUT1/4" x 3/4" HEX BOLT1/4" FLATWASHERWHEEL REMOVEDFOR ACCESS FIGURE 7 FIGURE 5 14. Assemble the flow control gauge to the hopper brace using the 1/4" x 3/4" carriage bolt, a nylon washer and the plastic knob. See figure 6. PLASTICKNOBNYLONWASHER1/4" x 3/4" CARRIAGE BOLTFLOWCONTROLGAUGE FIGURE 6 20. Assemble the chain cover to the frame assembly using two 1/4" x 5/8" hex bolts, 1/4" flat washers and 1/4" hex nuts as shown figure 9. 21. Install the hitch pin and the 1/8" hair cotter pin in the spreader hitch bracket and tongue. See figure 9. 16. To check for correct opening of hopper flow plates: a. Set the flow control gauge at the highest setting. b. Move the flow control arm away from the hopper until it rests against the gauge. The slots in the bottom of the hopper should now be completely open. The edge of the flow plates should be just clear of the ends all the slots. c. If the flow plates are not straight with the slots, screw one ferrule up or down on one side of the control rod. d. If the flow plates open to far or not far enough, screw both ferrules equally up or down on the control rod. d. Move the flow control arm toward the hopper to the off position. Verify that the slots in the bottom of the hopper are completely covered by the flow plates. e. Tighten the lock nuts and then loosen 1/4 turn. 17. To check for proper tension on the hopper flow plates: a. Set the flow control gauge at a mid range setting. b. Move the flow control arm against the gauge. c. Press firmly against the front of the flow plates at the bottom of the hopper. The flow control arm should not move. d. If the arm moves, tighten the hex lock nuts on the flow control arm until movement is prevented. 1/4" NYLOCK NUT1/4" x 5/8" HEX BOLT1/4" FLATWASHERCHAIN COVER1/8" HAIRCOTTER PIN3/8" HITCH PIN 18. Remove the two 5/16" lock washers and 5/16" hex nuts from the carriage bolts which are pre-assembled to the lift assembly arm. Attach the transport handle to the arm using the lock washers and hex nuts which you removed. See figure 8. 19. Assemble the handle grip to the transport handle. See figure 8. FIGURE 9 (2) 5/16" NYLOCK NUTS(PREASSEMBLED) TRANSPORT HANDLEHANDLE GRIP(2) 5/16" x 1" CARRIAGE BOLTS(PREASSEMBLED) FIGURE 8 SETTING CHART OPERATION HOW TO USE YOUR SPIKER/SPREADER 1. Refer to the instruction label on the material package and to the instruction decal on your spreader to help determine the proper spreader setting and application rate. Also see the Setting Chart on this page for a general range of settings for commonly used materials. 2. Loosen the knob and adjust the flow control gauge to the recommended setting. Retighten the knob. See figure 10. 3. Determine the approximate square footage of the area to be covered and estimate the amount of fertilizer or seed required. 4. Move th...