Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
Wa ter in en gine will short en the useful life of your tiller. • Clean engine, wheels, finish, etc. of all foreign matter. • Keep finished surfaces and wheels free of all gas o line, oil, etc. • Protect painted surfaces with au to mo tive type wax. 12 SERVICE AND ADJUSTMENTS CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into contact with plug. MID-WIDTH TILLING - 22" PATH (See Fig. 17) TILLER • Assemble holes “A” in tine hubs to holes “C” in tine shaft. TO ADJUST HANDLE HEIGHT (See Fig. 15) Factory assembly has provided lowest handle height. Se lect handle height best suited for your tilling conditions. Handle height will be different when tiller digs into soil. • If a higher handle height is desired, loosen the four nuts securing handle panel to engine brackets. • Slide handle panel to desired location. • Tighten the four nuts securely. NARROW TILLING/CULTIVATING - 12" PATH (See Fig. 18) • Remove outer tines. TINE ARRANGEMENT Your outer tines can be assembled in several different ways HANDLE PANEL ENGINE BRACKETS NUTS (ALSO 2 ON LEFT SIDE OF TILLER) Fig. 15 Fig. 17 tine_5 ACA C tine_6 INNER TINES ONLY Fig. 18 to suit your tilling or cultivating needs. NOTE: When reassembling outer tines, ensure right tine CAUTION: Tines are sharp. Wear assembly (marked “R”) and left tine assembly (marked “L”) gloves or other protection when han-are mounted to correct side of tine shaft. dling tines. NORMAL TILLING - 24" PATH (See Fig. 16) • Assemble holes “A” in tine hubs to holes “B” in tine shaft. tine_4 OUTER TINE INNER TINEHAIRPIN CLIP A B A B CLEVIS PIN Fig. 16 13 SERVICE AND ADJUSTMENTS TINE OPERATION CHECK (See Fig.19) WARNING: Disconnect spark plug wire from spark plug to prevent starting while checking tine operation. For proper tine operation, tine control lever must be against control body and all slack removed from inner wire of control cable when control is in the “OFF” (up) position. If lever and cable are loose, loosen cable clip at lower end of cable. Pull up on cable to remove slack, without extending spring on end of cable, and retighten cable clip. FINAL CHECK “OFF” POSITION • With tine control “OFF” (up), push down on handle to raise tines off the ground. • Slowly pull recoil starter handle while observing tines. Tines should not rotate. • If tines rotate, inner wire of control cable is too tight which is extending lower spring and engaging tines. Loosen cable clip and push down on cable only enough to relieve spring tension. Tighten cable clip. • Recheck in “OFF” position and adjust if necessary. FINAL CHECK “ON” POSITION • With tine control “ON” (held down to handle) push down on handle to raise tines off the ground. • Slowly pull recoil starter handle while observing tines. Tines should rotate forward. • If tines do not rotate, inner wire of control cable is too loose. Loosen cable clip and pull cable up to remove slack and retighten clip. • Recheck in “ON” position and adjust if necessary. NOTE: If “ON” position check required adjustment, re check “OFF” position adjustment ensure tines do not rotate when control is “OFF” (up). Fig. 19 TINE CONTROL “ON” POSITION TINE CONTROL “OFF” POSITION BODY CABLE CLIP TINE CON TROL CABLE TO REMOVE BELT GUARD (See Fig. 20) • Remove screws from side of belt guard. • Pull belt guard out and away from unit. • Replace belt guard by reversing above pr...
Otros modelos de este manual:Herramientas de jardín - 902032 (3.38 mb)
Herramientas de jardín - 902032 (3.38 mb)
Herramientas de jardín - 902032 (3.38 mb)
Herramientas de jardín - 902032 (3.38 mb)