Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
Attach tailwheel yoke spindle (#5) to boom weldment (#1) and secure with washers (#6 & #8) and roll pin (#7). RC15 Tailwheel Assembly Figure 1-3 14221 RC25 & RC35 Tailwheel Assembly Figure 1-3 14245 Driveline Installation 1. Grease input shaft on gearbox. 2. Slide the driveline end with the slip clutch or shearbolt over splined shaft of the gearbox and secure with locking device on driveline. 3-Point Tractor Hookup ! DANGER! Tractor hook-up can be hazardous to your health or that of your helper. Do not allow anyone to stand between the cutter and the tractor during hook-up operations. Do not operate the hydraulic 3-point lift controls while someone is directly behind the tractor. Refer to Figure 1-5: 1. Locate the cutter on a flat, level surface. 2. Determine the hitch category of the tractor that will be used: A Category I tractor will have a lower hitch link hole diameter of 7/8". The top link hole diameter (implement end) will be 3/4". A Category II tractor will have a lower hitch link hole diameter of 1 1/8". The top link hole diameter (implement end) will be 1". 3. Slowly back the tractorupto the cutteranduse the tractors 3- point hydraulic control to adjust the lower link arms up or down to match the height of the cutter hitch pins. ! DANGER! Engage parking brake, shut off tractor and remove key before dismounting from the tractor. 4. If the tractor is a Category I, simply position the lower link arms to "insert" the hitch pin into the lower hitch link hole. If the tractor is Category II, install the adaptor bushing on the hitch pin before insertion into the lower link hole. (Adapter bushing not required on RC2584 and all RC35 series rotary cutters.) 11 Section 1 Assembly and Setup 9/25/08 RC15, RC25, and RC35 Series Rotary Cutter 312-298M Land Pride Table of Contents 5. Install a 7/16" lynch pin or other fastener (supplied by customer) thru the hitch pin hole to lock the lower links into position. 6. Connect the driveline to the tractor’s PTO output shaft and secure with locking device on driveline. Connect the safety chain to the hitch brace on the cutter to restrict outer shield of driveline from rotating. 7. Connect the top link to the upper pivot hitch using the 3/4" hitch pin supplied. 8. Start the tractor and slowly engage the tractors hydraulic 3-point to lift the cutter. Check for sufficient drawbar clearance. Move the drawbar ahead, aside, or remove if required. Watch the telescoping movement of the driveline to ensure that it does not bottom out while lifting the 3-point. If the driveline does bottom out, it will require shortening: Refer to Figure 1-5: a. Hold the half shafts next to each other in the shortest working position and mark them. b. Shorten the inner and outer guard tubes equally. c. Shorten the inner and outer profiles by the same length as the guard tubes. d. Proper overlap is a minimum of one-half the length of each tube, with both tubes being of equal length. e. Round off all sharp edges and remove burrs. grease sliding profiles before re-assembly. NOTE: Chain should be attached at implement end of driveline. Cutting the PTO Shafts Figure 1-5 13588 9. If check chain kit is added. install as shown in Figure 1-6. Safety Guards Refer to Figure 1-7: After Rotary Cutter assembly is complete, tighten all hardware to the torque listed on Torque Values Chart in the “Appendix” section on page 26. 1. Install chain guard assembly (#1) to the cutter front angle using 1/2” -13 x 1 1/2” long bolts (#2) and whiz nuts (#3). 2. Install side chain guards (#4) to the bottom of cutter front angle using bolts (#2) and whiz nuts (#3). ! DANGER! Rotary cutters have the ability to discharge objects at high speeds; therefore, the use of front safety shields is strongly recommended when cutting along highways or in an area where people may be present. Check Chain Installation Figure 1-6 14247 Safety Guard Assembly Figure 1-7 14246 Table of Contents Land Pride Section 2 Operating Instructions Transporting ! CAUTION! When traveling on public roads at night or during the day, use accessory lights and devices for adequate warning to operator’s of other vehicles. Comply with all federal, state and local laws. NOTE: Always disengage the tractor’s PTO before raising the cutter to transport position. 1. When raising the cutter to the transport position be sure that driveline does not contact tractor or cutter. 2. Be sure to reduce tractor ground speed when turning; and, leave enough clearance so the cutter does not contact obstacles such as buildings, trees or fences. 3. Select a safe ground speed when transporting from one area to another. When traveling on roadways, transport in such a way that faster moving vehicles may pass you safely. 4. When traveling over rough or hilly terrain, shift tractor to a lower gear. Operating Check List In addition to design and configuration of equipment; hazard control and accident prevention are dependent upon the awareness, concern, prudence and proper training involved...
Otros modelos de este manual:Herramientas de jardín - RC15 Series (5.46 mb)
Herramientas de jardín - RC35 Series (5.46 mb)