Iniciar sesión:
Votos - 3, Puntuación media: 4 ( )

Manual de usuario Bush Hog, modelo RTN

Fabricar: Bush Hog
Tamaño del archivo: 10.44 mb
Nombre del archivo:
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


Traveling at the slowest forward speed with rear shield fully lowered will give finest possible finish. This shield adjustment is good for mulching, mixing, and burying weeds, fertilizer, etc. The more you increase forward speed and shield height, the coars- er the finished results will be. To leave the ground surface rough with larger clods and residue exposed, work with shield fully raised. When working in rocky soil, always have shield in raised position. Figure 3-1 Adjustments Adjustable, Spring-Loaded Shock Absorber 3-3 OPERATION A. Perform BEFORE EACH USE maintenance listed in paragraph 4-1. B. Adjust for work per paragraph 3-2. C. Start tractor. Raise tiller off the ground. D. With tractor at idle speed, engage PTO drive. DANGER STAY CLEAR OF ROTATING DRIVELINES. DO NOT OPERATE WITHOUT DRIVELINE SHIELDS IN PLACE AND IN GOOD CONDI- TION. FAILURE TO HEED THESE WARN- INGS MAY RESULT IN PERSONAL INJURY OR DEATH. DANGER KEEP HANDS AND FEET FROM UNDER MACHINE AT ALL TIMES. MAKE CERTAIN EVERYONE IS CLEAR OF MACHINE BEFORE OPERATING. FAILURE TO HEED THESE WARNINGS MAY RESULT IN PER- SONAL INJURY OR DEATH. E. Place tractor in gear and proceed forward. Increase speed to 3/4 throttle. Lower tiller into soil. Increase speed to 540 PTO rpm. Average soil with reasonable moisture will allow travel speeds up to 2 mph. Hard soil will require low travel speed, less than 1 mph to ensure smooth operation and maxi- mum possible depth. Shallow weed cultivation will allow speeds up to 3 mph. At the end of a pass lift tiller clear of ground before making a turn. After turn- ing, proceed back across field, slowly lowering the tiller into the soil. Do not turn with tiller in the ground as this can damage tiller and tractor link- age. Never use reverse gear while tiller is low- ered into ground. Avoid operating tiller in the raised position. 3-4 TRANSPORTING Do not engage PTO drive while transporting tiller. Obey all state and local laws when transporting on public roads. Always use flashing warning lights unless prohibited by law. RearShieldHeightAdjusterSkidParkingStand 9 SECTION IV MAINTENANCE 4-1 MAINTENANCE CHECK LIST Perform scheduled maintenance as outlined below. Lower machine to ground, turn off tractor and set parking brake before doing maintenance inspections or work. Some checks may require raising machine off ground and supporting with blocks. All bolts should be torqued as recommended in TORQUE SPECIFICATIONS, unless otherwise indicated. BEFORE EACH USE 1. Check tractor tire air pressure. Refer to tractor operator’s manual. WARNING THE TILLER CAN FALL FROM HYDRAULIC SYSTEM FAILURE. TO AVOID SERIOUS INJURY OR DEATH, SECURELY SUPPORT TILLER BEFORE WORKING UNDERNEATH. 2. Check blades and rotor to be sure that no foreign objects such as wire or steel strapping bands are wrapped around them. 3. Check blade bolts for tightness. Tighten to 118 ft./lbs. 4. Inspect blades for wear. Replace if necessary. 5. Make certain driveline shields are in place and in good repair. 6. Perform BEFORE EACH USE lubrication per paragraph 4-2. 7. During operation, listen for abnormal sounds Figure 4-1 Lubrication To remove yoke shield, depress the three tabs with a screwdriver and slide cover back. RTH Gear Drive Oil Filler Plug RTHCheckPlug(5)BeforeEachUse (7) 40 Hours (1)BeforeEachUse(3)BeforeEachUse (2)BeforeEachUse which might indicate loose parts, damaged bear- ings, or other damage. AFTER EACH USE 1. Clean all debris from machine especially underside. 2. Store in dry place. 4-2 LUBRICATION (Figure 4-1) NOTE The multi-purpose grease referenced in this sec- tion is an NLGI Grade 2 type grease. BEFORE EACH USE 1. Driveline Universal Joints -Apply multi-purpose grease with grease gun. 2. Driveline Guard -Apply 2-3 shots of multi- purpose grease with grease gun to plastic fitting. 3. Driveline -Disconnect PTO driveline, pull the two sections apart, apply thin coat of multi-purpose grease to inside of outer (female) section. Reassemble sections and install. Pull each sec tion to be sure driveline and shields are securely connected. Make certain PTO shielding is in good condition. 4. Input Gearbox -Add EP80W-90 gear oil, if necessary, to bring oil level to check plug. 5....

Otros modelos de este manual:
Herramientas de jardín - RTH (10.44 mb)
Herramientas de jardín - RTH (10.44 mb)
Herramientas de jardín - RTH (10.44 mb)
Herramientas de jardín - RTN (10.44 mb)

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría