Votos - 4, Puntuación media: 4.5
(
)
)
|
Resumen del manual
25.Use a sharp blade. A dull blade is more likely to snag and thrust. Replace the fastening nut according to the manufacturer's instruction. 26.Cut only material recommended by the manufacturer. Do not let the blade contact material it cannot cut, such as rocks, metal etc. 27.Always wear safety boots, additionally a helmet is required if there is a risk of contact with falling objects. 1-9 Minamidai, Kawagoe, Saitama, 350-1165 Japan 3 Setup Setup ¦ ENGINE A: BC2310LE/BC2610LE/WE 1. Loosen the bolts temporarily attached to the clutch housing. 2. Push the drivershaft toward the gearcase and rotate it by hand to check that the driveshaft is engaged with the gears. 3. Insert the shaft tube into the clutch housing until it bottoms. When difficult to engage, twist the engine slightly. 4. Align the positioning holes on the clutch housing and the shaft tube and fit the bolt into the holes. And fasten the tightning bolts by turns securely. (Tightning torque: 4.9~7.8N.m. BC2310LE (0.5~0.8kgm)) (1) Positioning hole (2) Bolt (M5x10) (3) Tightning bolt (M5x22) BC2610LE/WE B: BC3500LE/WE/BC4500WE/BC530WE • Using attached 4 socket screws, secure the connection firmly with equal force. BC3500WE BC4500WE BC530WE ¦ HANDLE A: BC2310LE/BC2610LE/BC3500LE • Put the handle onto the main pipe and fix it with 4 screws. BC2310LE BC2610LEBC3500LE B: BC530WE • BC530WE only remove the screw(1) from the right grip(2) and put the grip onto the right handle. Align the positioning holes and put the screw through them. Fasten the clamp(3). And thencontinue to C. BC530WE C: BC2610WE 1. Loosen the 4 bolts on the upper cap and insert the handles equally. Retighten the bolts. 2. Put the handle assembly into the bracket and put the upper cap over it. Tighten the cap securely. D: BC3500WE/BC4500WE/BC530WE 1. Remove the upper cap from the bracket. 2. Loosen the 4 bolts on the clamp and insert the handles equally. Retighten the bolts. 3. Put the handle assembly into the bracket and put the upper cap over it. Tighten the cap securely. BC2610WE BC3500WE BC4500WE BC530WE ¦ CONNECTING THROTTLE WIRE [EXCEPT BC530] 1. Remove the air cleaner cover. 2. Connect the end of the throttle wire to the joint on the top of the carburetor. 2. 1. ¦ CONNECTING SWITCH WIRES • Connect the switch wires between the engine and the main unit. ¦ PROTECTOR • Wrap the protector around the outer pipe as shown in the figure, and fasten the magic ¦ BLADE GUARD fastener. BC2610WE BC3500WE BC4500WE BC530WE • Attach the guard to the clamp on the outer pipe just touching the gearcase. Fix it with 2 bolts. ¦ INSTALLING CUTTING HEAD 1. While locking the gear shaft by inserting the attached bar into the upper holder and the gear box, loosen and remove the hexagon bolt(left-handed) 2. Using the arbor bolt, screw in the cutting head to the gear shaft over the holders. Hand-tighten it securely. 4 Fuel WARNING • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and ...
Otros modelos de este manual:Herramientas de jardín - BC2300LE (712.79 kb)
Herramientas de jardín - BC2310LE (712.79 kb)
Herramientas de jardín - BC2610LE (712.79 kb)
Herramientas de jardín - BC2610LE/WE (712.79 kb)