Votos - 3, Puntuación media: 4.7 ( )

Fabricar: Bolens Tamaño del archivo: 2.36 mb Nombre del archivo: Idioma del manual:

1 12 9808 Locknut-hex hd., 5/16"-18............ 1 37 1901086 8HP Kohler MagnumEngine-recoil start. 13 9710 Bolt-flanged hex hd., 3/8-16 x 1".. 5 Model No. M8T. Specification No. 14 9913 Lockwasher-spring lock, 3/8"........ 5 PS-301608. Solid state electronic 15 9904 Washer-flat, 3/8", S.A.E................ 7 ignition, horizontal crankshaft is 16 2146 Bushing-spacer, 21/64“ (.325"lg.). 2 turned down to 3/4" at PTO end to 17 1113-1 Bushing-spacer, 19/64" (,300'lg.). 2 accept engine pulley. See NOTE 1 18 9120 Ring-retaining (tolerance ring)... 1 below......................................... 1 37 1901087 8HP Kohler Magnum Engine-electric BELT DRIVE SYSTEM start. Model No. M8ST. Specifi- 19 1920 Block—belt adjustment, 3-7/8" (incl cation No. PS-301609. Same as Ref. No.’s 13,15, and 20) 1 engine above, but with electric 20 2100 Rod-belt adjust., 7“ with measuring starting. For use with tillers already gauge......................................... 1 equipped with the Key Switch 21 1900766 Decal-engine stabilization, for Starting System (see page 18). Briggs & Stratton engine........... See NOTE 1 below..................... 1 22 9715 Bolt-hex hd., 3/8-24x1-1/2" 1 38 55053 Decal-hot surface safety warning.. 2 23 1919 Disc-reverse, (incl. Ref. No. 19)... 1 39 1900767 Decal-engine stabilization, for 24 9245 Belt-forward drive (no substitute Kohler engine............................ 1 recommended due to extra 40 2522 Engine Weight-for Briggs & Stratton strength required)...................... 1 engine only................................ 1 25 1483 Pulley—engine power take off...... 1 41 9966 Bolt-hex hd., 5/16-18x2-1/4”, 26 1138-1 Shim-engine pulley, 1/16" thick.... As Grade 5...................................... 2 Req'd 42 20553 Spacer-zinc plated........................ 2 26 1138-2 Shim-same as above, 1/32" thick. As Req'd WHEEL & TIRE ASSEMBLIES 27 9303 Key-engine pulley, 3/16"sq. x 2-1/2" 1 43 9322 Pin—roll, 5/16" x 1-1/2".................. 2 45 2709-01 Wheel & Tire Assy-bar tread, left ENGINES AND ENGINE MOUNT side, 4:80 x 8" tubeless tire with 28 90008 Bolt-hex hd., 5/16-18x1", Grade5.. 2 valve stem, mounted on single- 29 9801 Nut-hex, 5/16"-18......................... 4 piece steel wheel....................... 1 30 1034 Bar-engine mounting.................... 2 45A 2709-02 Wheel & Tire Assy-bar tread, right 31 9147 Plug-thread protector, red plastic. 2 side. Same as above but for right 32 9572 Bolt-hex hd., 5/16-24x1-1/8" 4 side of tiller................................ 1 33 9912 Lockwasher-spring lock, 5/16", , 6 46 1902020 Cap-wheel hub............................. 2 34 2565 Mount-engineto tiller................... 1 NOTE 1—Please call or write Technical Service Dept, before ordering replacement engine. NOTE 2-For correct traction and directional control, Bar Tread Tires should be mounted on the tiller so that the closed end of the “V” in the tire tread on top of the tire will face forward. 5 TROY-BILT® HORSE TILLER MODELS 12068, 12069, 12070 AND 12071 DEPTH REGULATOR & TINE HOOD ASSEMBLIES (Figure 4) 1 6 MODELS 12068, 12069, 12070 AND 12071 TROY-BILT® HORSE TILLER REF PART REF PART No. No. DESCRIPTION QTY. No. No. DESCRIPTION 1 9712 Bolt-hex hd., 3/8-16 x 1-1/4"...... . 2 11 This Ref. No. not used.................. 2 1113-1 Bushing-19/64" (.300" Ig.).......... . 2 12 9929 Washer-flat, 5/16”......................... 3 9913 Lockwasher-spring lock, 3/8"..... . 2 13 2629 Hood—(incl. Ref. No. 14)............... 4 9802 Nut-hex, 3/8"-16......................... . 2 14 2719 Decal-hood, operating instructions. 5 1117A Bar-depth regulator (incl. Ref. No.’s 6 and 7).......................... 1 15 2527 Bracket—(incl. Ref. No. 16)............ 6 9120 Ring-retaining............................ . 1 16 9308 Pin-roll (spiral) 1/4" x 1”............... 7 9119 Knob-depth regulator (incl. Ref. 17 9534 Spacer........................................... No. 6)...................................... . 1 18 9384 Spring........................................... 8 1900867010 Bar-drag, depth regulator........... . 1 19 9734 Bolt-hex hd., 1/4-20x1"................. 9 9552 Screw-thread-forming, 20 9811 Locknut-1/4"-20........................... 1/4-20x1/2"............................ . 2 21 90038 Bolt-flanged hex hd., 10 90044 Bolt-flanged hex hd., 5/16-18x3/4”.......................... . 2 5/16-18x5/8"............................ 7 TROY-BILT® HORSE TILLER MODELS 12068, 12069, 12070 AND 12071 POWER UNIT TRANSMISSION ASSEMBLIES (Figure 5) MODELS 12068, 12069, 12070 AND 12071 TROY-BILT® HORSE TILLER REF PART REF PART No. No. DESCRIPTION QTY. No. No. DESCRIPTION QT\ TRANSMISSION COVER & SHIFT LEVER external...................................... 2 BRACKET ASSEMBLIES 29 2461 Eccentric-shaft, tines/PTO clutch 1 9782 Bolt-hex hd., #10-32 x 3/8", self-locking ...

Descargar ahora

Introduzca dos números de la imagen: