Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
PRICES. PRICES OUTSIDE OF U.S.A. SUBJECT TO LOCAL IMPORT DUTIES, TAXES, ETC. REPAIR PARTS 20" BRUSH AND LOG SAW j—-;-—Order by Parf Number-:- Item No. Pait No. 1 2 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 F-AX5 DA-10 103001 S1A41A S1BX1 SW-A12 SW-A13 SW-A5 SW-A37 SW-A39 SW-A40 SW-A42 110003 SW-AX2 SW-AX5 SW-B2A SW-B14 110001 SW-BX2 SW-BX3 S1A45A S1AX18 SW-A29 Name o! Part Idler Pulley '* §0 Set Collar (Arbor Shaft) YV^tO/p Hitch Side Plate , T-Nut - Hitch Clamp Assembly -vi'*7 Lower Flange — )Qt i— Upper Flange - i Clamp - Y’dCfCO'i Spacer ^ 3cjOd 7 „ Arbor Prop J ? . Tightener Screw Set Collar (Tightener Assembly) 5 3 A-56 Super Combine V Belt $ y " Tightener Assembly .Preys' Clutch Assembly -« ^ fSt- 5” Bearing Housing with ijusnmgs „ Xf^ Arbor - £>dc&Ot'4 Idler Bracket Arbor Holder Assembly «• $3C&S0 Frame Assembly - > *3 Spring Clip - %/Lfo'f.f - „ Rod Socket Assembly / if 20" Cordwood Saw Blade (I3/®” Bore) Ship. Wt. Lbs. Oz 1 2 I &¥• I . \xJ 9 15 ÏÉL. 12 7 12 4 4 4 10 8 12 10 8 6 ,12 2 8 8 2 4 Price Each 5 1.00 .45 .15 .50 1.00 1.40 1.70 .30 .30 .70 .55 .45 3.25 2.10 13.50 3.30 9.30 1.60 6.60 9.90 .20 .90 10.90 Item No. Part No. Name of Part Ship. Wt. Price Each Lbs. Oz. 25 SW-B1A Stand Rod - ŸâCetfiQ} 1 .55 26 SW-C1 Stand i'3 C 30 c / 4 1.45 27 S2A-22A Set Collar {Stand Rodjcf/7/W'*-' 3 .50 28 Hex Full Nut, L.H. 6 .18 34 110002 Belt Support 5 .50 #1641 Grease Fittings 2 .10 PARTS NOT ILLUSTRATED A B C S1LA73 S2A43 SWISS' Inner Bearing Race 7t C:'}3 Bushing for Bearing Housing Pulley Key №cf0(*L *43 4 5 5 $ .40 .55 .20 SAW CRADLE 29 30 31 32 33 SW-A5 SW-A19 SW-A27 SW-CX3 SW-CX4 Clamp " -Cradle Holder -* t 3 C / O f *7 ^ Cradle Chain (12") Cradle Assembly * ^¿>^0 , Cradle Frame Assembly^3£ OH 1 1 te 18 10 12 8 $ .30 .55 .20 6.75 8.90 -itho in U.S.A. M.P. _ Product Number 930196 ATTACHING 2011 BRUSH & LOG SAW TO MODEL MWM TRACTOR The 20" Brush and. Log Saw is attached to the Model "W" tractor by following the instructions as shown in the instruction manual. The only variations in attaching are listed below. When attaching the saw frame to the Model "W” tractor, the QUICK HITCH is inserted into the 2nd and 4th holes from the back of the saw frame, Add the Clevis #102039 to the stand, using a 5/16"-18NCx 3/4" long capscrew, lockwasher and hex nut. This clevis acts as an extension into which the lower control rod attaches. • PORT WASHINGTON, WISCONSIN PACKING LIST The complete saw is shipped in a carton with saw blade separate. The cradle attachment is packed in a separate carton. MOUNTING FRAME AND CONTROLS G4UTfON; Do not Aave motor running wfien attaching sow. 1. Attach the saw frame (1, Fig. 1) to the patented QUICK-HITCH (2, Fig. 1) on the front of the tractor. 2, Tighten the two T nuts on QUICK-HITCH and drop stand (3, Fig, 1) into position on ground. NOTE: QUICK-HITCH is inserted in first and third holes from back of frame for 2 and 2 x/z H.P, tractors and second and fourth holes for use with 5 H.P. tractors. 3. Attach stand rod (4, Fig. 1) to stand and to lower clutch lever with spring clips. 4, Be sure stand remains bolted securely to saw frame to prevent it from passing stop and damaging saw blade. Figure I — Saw Mounted in Horizontal Position IMPORTANT! This is a cordwood saw, guaranteed to be free from defects and properly tempered. It is not guaranteed against breakage of teeth, as this is under the control of the operator. MOUNTING SAW IN HORIZONTAL POSITION ( 1. Remove one screw from arbor holder clamp (5, Fig. 1) and insert arbor in vertical position as illustrated in Figure 1. 2. Raise idler bracket (6, Fig. 1) until parallel to arbor shaft and tighten carriage bolt. 3. Remove key from small bag attached to pulley, and insert in pulley key way under set screw. 4. Place pulley on arbor shaft so that it lines up with idler pulley; then tighten set screw. 5. Place A-56 Special Belt (7, Fig. 1) over arbor pulley and over middle groove of engine pulley so belt rides on idler pulley inside of belt support, (A, Fig. 1) as shown. 6. Tighten set collar (8, Fig. 1) on adjusting screw assembly and turn tightener screw <9, Fig. 1} until belt is tight; then lock with nut (10, Fig. 1). 7. Remove left hand hex nut and flange from end of arbor shaft. Place saw blade as shown in Figure 1 over end of arbor and secure it with flange and hex nut. To insure tightness tap wrench with hammer. When the saw is in horizontal position mounted on the Model FA 2V2 H.P. or Model VA 5 H.P. tractors, the following is recommended. * Remove the ratchet pawl assembly (Part 152009) from the ratchet cage. This will afford ease of maneuverability and operation, particularly in close work or in felling trees. Ratchet pawl assembly may be replaced when cutting brush, bucking, limbing, or in use with the tilting frame. NOTE; Belt leaving idler pulley should e...
Otros modelos de este manual:Herramientas de jardín - 990032 (1.08 mb)