Votos - 3, Puntuación media: 5
(
)
)
|
Resumen del manual
If there is any damage, do not use until damage is repaired by your authorized service dealer. S Do not use the unit if the switch does not turn the unit on and off properly. Have the unit repaired by your authorized service dealer. S Do not use with damaged cord or plug. If unit is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to your authorized service dealer for repair. S Avoid unintentional starting of the unit. Never carry unit with your finger on the switch. Be sure the switch is in the off position and never touch the switch when connecting extension cord. S Unplug the unit from the power source when not in use, before servicing, and when changing accessories and/or attachments. S Avoid any body contact with any grounded conductor, such as metal fences, or pipes, to avoid the possibility of electric shock. S Ground Fault Circuit Interrupter (GFCI) protection should be provided on the circuit or outlet to be used for the unit. Receptacles are available having built-in GFCI protection and may be used for this measure of safety. UNIT/MAINTENANCE SAFETY WARNING: Always stop unit and disconnect spark plug wire (or disconnect unit from power source) before performing maintenance. S Inspect entire unit before each use. Replace damaged parts. Check for fuel leaks. Make sure all fasteners are in place and securely fastened. S Maintain unit according to recommended procedures. S Use only recommended Poulan PRO parts and accessories. S Be sure chain stops moving when engine idles (see CARBURETOR ADJUSTMENTS section of original manual). S Keep others away when making carburetor adjustments. S Never start the unit with the clutch housing removed. The clutch can fly off and cause serious injury. S Keep the handles driy, clean, and free of oil or fuel mixture. S Keep fuel and oil caps, screws, and fasteners securely tightened. S Have all maintenance and service not explained in this manual performed by an authorized service dealer. OPERATE YOUR PRUNER SAFELY S Operate the pruner only in a well-ventilated outdoor area. S Do not use a pruner to cut down trees or any portion of the tree trunk. S Only use for pruning limbs or branches overhead not greater than 6 inches (15 cm) in diameter. S Do not cut small brush and saplings with the pruner. Slender matter may catch in the chain and be whipped toward you, pulling you off balance. S Make sure the chain will not make contact with any object while starting the engine. Never try to start the unit when the guide bar is in a cut. 4 S Do not put pressure on the pruner at the end of the cut. Applying pressure can cause you to lose control when the cut is completed. S Do not run the unit at high speed when not pruning. S If you strike or become entangled with a foreign object, stop the engine immediately and check for damage. Have any damage repaired by an authorized service dealer before attempting further operations. S Do not operate a pruner that is damaged, improperly adjusted, or not completely and securely assembled. Always replace bar and chain immediately if it becomes damaged, broken or is otherwise removed. S Always stop the unit when work is delayed or when walking from one cutting location to another. Stop the engine before setting the unit down. S Use only in daylight or good artificial light. S Use only for jobs explained in this manual. KICKBACK WARNING: Avoid kickback which can result in serious injury. Kickback is the backward, upward or sudden forward motion of the guide bar occurring when the chain near the upper tip of the guide bar contacts any object such as a log or branch, or when the wood closes in and pinches the chain in the cut. Contacting a foreign object in the wood can also result in loss of control. S Rotational Kickback can occur when the moving chain contacts an object at the upper tip of the guide bar. This contact can cause the chain to dig into the object, which stops the chain for an instant. The result is a lightning fast, reverse reaction which kicks the guide bar up and back toward the operator. S Pinch-Kickback can occur when the wood closes in and pinches the moving chain in the cut along the top of the guide bar and the chain is suddenly stopped. This sudden stopping of the chain results in a reversal of the chain force used to cut wood and causes the pruner to move in the opposite direction of the chain rotation. The pruner is driven straight back toward the operator. S Pull-In can occur when the moving chain contacts a foreign object in the wood in the cut along the bottom of the guide bar and the chain is suddenly stopped. This sudden stopping pulls the pruner forward and away from the operator and could easily cause the operator to lose control of the pruner. REDUCE THE CHANCE OF KICKBACK S Recognize that kickback can happen. With a basic understanding of kickback, you can reduce the element of surprise which contributes to accidents. S Never let the moving chain contact any...
Otros modelos de este manual:Herramientas de jardín - 115261226 (217.82 kb)
Herramientas de jardín - PP5500P (217.82 kb)