Votos - 3, Puntuación media: 5
(
)
)
|
Resumen del manual
Hd. 1/4"x1/4" 41 S-7186 2 Set Screw - Skt. Hd. 1/4"x1/4" 42 S-6369 4 Carriage Bolt, 1/4"x3/4" 42 S-6369 4 Carriage Bolt, 1/4"x3/4" 43 2FH0687 2 Machine Screw -Rd. Hd.#4-40x5/8" 43 2FH0687 2 Machine Screw -Rd. Hd.#4-40x5/8" 44 S-1101 6 Hex Bolt, 1/4"x1/2" 44 S-1101 6 Hex Bolt, 1/4"x1/2" 45 S-8072 4 Hex Bolt, 5/16"x3/4" 45 S-8072 4 Hex Bolt, 5/16"x3/4" 46 S-7521 2 Hex Bolt, 3/8"x 1 1/2" 46 S-7521 2 Hex Bolt, 3/8"x 1 1/2" 47 S-7744 1 Hex Bolt, 3/8" x 5-1/2" 47 S-7744 1 Hex Bolt, 3/8" x 5-1/2" 48 2FH0990 3 Hex Flange Wiz Lk.Scr., 5/16"x1" 48 2FH0990 3 Hex Flange Wiz Lk.Scr., 5/16"x1" 49 3FH0530 2 Pop Rivet-3/16" Aluminum 49 3FH0530 2 Pop Rivet-3/16" Aluminum 50 3FH0567 1 Snap Ring 1" 50 3FH0567 1 Snap Ring 1" 51 S-9159 1 Cotter Pin, 1/8"x3/4" 51 S-9159 1 Cotter Pin, 1/8"x3/4" 52 S-2041 4 Lock Washer, 1/4" 52 S-2041 4 Lock Washer, 1/4" 53 S-1147 10 Lock Washer, 5/16" 53 S-1147 10 Lock Washer, 5/16" 54 S-1054 2 Lock Washer, 3/8" 54 S-1054 2 Lock Washer, 3/8" 55 S-1430 8 Flat Washer, 1/4" 55 S-1430 8 Flat Washer, 1/4" 56 S-1937 12 Flat Washer, SAE, 5/16" 56 S-1937 12 Flat Washer, SAE, 5/16" 57 3FH0999 1 Key - Woodruff(Tab Type) 1/4" x1" 57 3FH0999 1 Key - Woodruff(Tab Type) 1/4" x1" 58 S-6371 1 Key - Square, 1/8"x1" 58 3FH1015 1 Key - Square, 3/16"x1" 59 Not used on 918 Bin Level 59 3FH0830 3 Machinery Bushing, 1"x1-1/2"x10GA Installation and Operation Bin Level Bin Level TROUBLE SHOOTING PROBLEM CORRECTION Grain is high on one side of bin. (a) Spreader is not hung level. (b) Spreader not stopping & starting properly during filling. See Figure 2. (c) Spreader running continuously. Grain is high at the center of bin. (a) Slide Gate open too far. (b) Spreader stopping too long, letting too much grain through slide gate. See Figure 4. (c) Outside ring set too low. See Figure 3. Grain is low at the center of bin. (a) Slide Gate not open far enough. (b) Spreader not stopping enough to let grain out through slide gate. See Figures 2 and 4. (c) Outside ring set too high. See Figure 3. Grain forms “doughnut” a few feet from bin wall. Caused by grain bouncing off bin wall excessively. (a) Adjust outside ring. See Figure 3. (b) Hook Spreader higher in the roof cone to increase grain bouncing off underside of roof and then being deflected straight downward. (c) Open slide gate more to help fill center. (d) Spreader model not correct for bin size. Grain not getting all the way to the wall. (a) The Model 918 Bin Level will only spread over an entire bin width of up to 30’ and the Model 936 up to 36’. If the bin is bigger, lower sides will result because grain will not throw out far enough. (b) Adjust outside ring up. See Figure 3. (c) Bin Level hanging too high under bin roof. (d) Rubber drive wheel badly worn. Spreader swings excessively This condition is caused by improper hooking up of the suspension chains. There should be the same number of links from spreader to hook with all six strands of chain. This will also usually ensure level hanging of the Spreader. Equal spacing of hanger brackets is important. The hanger brackets should be on the outer fill-hole ring. Spreader does not run. (a) Mercury switch plate may be frozen shut or plugged with foreign material. (b) Rubber drive wheel may be slipping because of excessive moisture or broken mounting plate spring. (c) Motor overload may have tripped. It will reset automatically after the motor has cooled. (d) Blown fuse or broken wire. (e) Faulty mercury switch. (f) Mercury switch plate bent out of shape. (g) Grain extremely high moisture may not flow enough to operate the mercury switch plate. Bending section of the plate holding the mercury switch up to make it more sensitive may help. (h) The motor will not start and will “chatter” if the voltage is too high. (i) The motor will not start and will “hum” if the voltage is too low. See Table A on Page 8 for the proper length and size of wiring to prevent excessive voltage drop. Motor slows down when loaded. (a) Motor wired for the wrong direction. Pan should turn clockwise when viewed from the top. Bin Level NOTES Bin Level The GSI Group, Inc. Warranty THE GSI GROUP, INC. (“GSI”) WARRANTS ALL PRODUCTS WHICH IT MANUFACTURES TO BE FREE OF DEFECTS IN MATERIAL AND WORKMANSHIP UNDER NORMAL USAGE AND CONDITIONS FOR A PERIOD OF 12 MONTHS AFTER RETAIL SALE TO THE ORIGINAL END USER. THE PURCHASER’S SOLE REMEDY AND GSI’S ONLY OBLIGATION SHALL BE TO REPAIR OR REPLACE, AT GSI’S OPTION AND EXPENSE, PRODUCTS THAT, IN GSI’S SOLE JUDGMENT, CONTAIN A MATERIAL DEFECT DUE TO MATERIALS OR WORKMANSHIP. ALL DELIVERY AND SHIPMENT CHARGES TO AND FROM GSI’S FACTORY WILL BE PURCHASER’S RESPONSIBILITY. EXPENSES INCURRED BY OR ON BEHALF OF THE PURCHASER WITHOUT PRIOR WRITTEN AUTHORIZATION FROM AN AUTHORIZED EMPLOYEE OF GSI SHALL BE THE SOLE RESPONSIBILITY OF THE PURCHASER. EXCEPT FOR THE LIMITED WARRANTY EXPRESSED ABOVE, GSI MAKES NO FURTHER WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY OR FITNES...
Otros modelos de este manual:Herramientas de jardín - 936 (202.34 kb)