Votos - 2, Puntuación media: 5
(
)
)
|
Resumen del manual
LONG HAY OR STRAW MUST CONTAIN MANURE IN ORDER TO BE SPREAD. FAILURE TO COMPLY MAY DAMAGE THE DRIVETRAIN AND VOID THE WARRANTY. The rear spinners have been designed and tested to provide the best spread pattern for most liquids and semi solid manure. However, the pattern will vary for each specific condition. The factors that contribute most to differing patterns will be moisture content and the amount and length of bedding material. For most typical conditions, the spread pattern should be uniform and about 15 ft. wide. When this is the case, plan your spreading patterns so you do not have to travel over previously spread manure which will be slippery, resulting in poor traction. Traction on wet grass is also poor. When the resulting pattern may require that you overlap during spreading, use precautions on slopes and hills where you could experience a loss of traction by traveling over ground with previously spread manure. NOTE: Further control of the application rate is possible by the relationship of tractor engine speed to ground speed (transmission gear selection). For optimum, trouble-free performance it is necessary to operate at or near engine PTO speed. When the spreader is empty, idle the tractor and stop the PTO. Close the flow control rear gate. WARNING: NEVER OPERATE PTO ABOVE ITS NORMAL 540 RPM RATING. NEVER CONNECT SPREADER PTO SHAFT TO A 1000 RPM TRACTOR PTO, UNLESS THE SPREADER IS EQUIPPED WITH A 1000 RPM OPTIONAL KIT. TRACTOR PTO MUST MATCH IMPLEMENT PTO. FAILURE TO HEED MAY RESULT IN SPREADER DAMAGE OR SERIOUS PERSONAL INJURY. NOTE: Failure to idle the tractor before disengaging the PTO will cause roller chain over-running and damage to the chain tighteners. NOTE: Maximum life of the PTO shaft universal joints will result if you stop the PTO while making turns at the end of the field. CAUTION: DO NOT EXCEED THE MAXIMUM 80. TURNING ANGLE ON THE CONSTANT VELOCITY PTO DRIVE LINE. EXCEEDING THE TURNING ANGLE WILL DAMAGE THE CONSTANT VELOCITY “CENTER HOUSING” AND WILL EXERT EXCESSIVE PRESSURES ON THE PTO INPUT CENTER SHAFT AND RELATED BEARINGS. OPTIONAL SHEAR SPROCKET INSTRUCTIONS The Meyer Spreader you have received has been equipped with a shear sprocket design on the main auger drive sprockets. The augers are being driven by two .” allen head grade 8 bolts. The design is such that if the bolts are sheared another set of holes to install new shear bolts will always be accessible without turning over the machine. DANGER: AT NO TIME SHOULD INSTALLATION BE DONE WITH ANYONE ON THE TRACTOR. SHUT THE TRACTOR OFF, REMOVE THE KEY AND DISCONNECT THE DRIVE LINE BEFORE DOING ANY SERVICE ON THIS MACHINE. SERIOUS INJURY OR DEATH MAY OCCUR IF SAFETY IS NOT FOLLOWED. The plate sprocket is set up with the initial drive bolts being .” diameter. An extra set of holes for 9/16” drive bolts are located on the sprocket if a additional shear strength is needed due to shear bolt failure from obstruction. If the .” bolts shear, replace with the same .” diameter bolts after obstruction is removed. DO NOT JUMP TO THE UP TO THE NEXT SIZE BOLT. Install the new bolts in the proper way as to drive off of the head of the bolt, not the nut. The two different size holes available (. & 9/16”) are close in size. Be sure to install the proper size bolt into the correct size hole. Shear or sprocket failure will occur if assembled incorrectly! Recommended procedure to follow if shear does occur. If only one auger shears unload the opposite side of spreader and remove obstruction from sheared side of machine. After obstruction has been removed install new shear bolts in sheared auger and unload Model V-Max —13— the remainder of the load. If both sides do shear install only one set of auger shear bolts and unload one side at a time. After first side is unloaded install bolts in opposite side and unload the remainder of the spreader. If a second shear has happened without obstruction in the auger, install the next larger size shear bolt. As the shear bolt size is increased the protection on the machine is going to decrease. The potential for equipment damage is greater. Order replacement bolts and nuts from the chart below. Part # Description 831-5020-1.75 .-20x1-3/4” Allen Head Cap Bolt 884-5020 .-20 Top Locknut Grade 8 831-5618-1.75 9/16-18x1-3/4” Allen Head Cap Bolt 884-5618 9/16-18 Top Locknut Grade 8 910-0101 120B33 Shear Sprocket Assembly Complete STORAGE AFTER USE WARNING: DISCONNECT PTO DRIVE SHAFT AND HYDRAULIC HOSES BEFORE CLEANING, ADJUSTING, OR SERVICING THIS MACHINE. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH. Before storing this spreader for an extended period of time perform the following: Allow the spreader to completely clean out the last load. Thoroughly hose off all manure from the outside of the spreader and the inside of the box, particularly getting the flow control rear gate mechanism clean. The wash water can be drained into your manure storage pit, or if the gate is left closed, the wate...
Otros modelos de este manual:Herramientas de jardín - V- MAX 2636 (3.51 mb)
Herramientas de jardín - V- MAX 3954 (3.51 mb)