Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Check regularly for any observable oil leakage. If oil leakage is excessive, replace required input/output shaft oil seals. Use ONLY EP #80-90 wt. gear lube oil or an equivalent in corner box, only Lighter weight gear lube oil may be used in temperatures lower than 20°F. Change oil in the gearboxes after the first season of use and regularly thereafter. L13 Grease (1) brass bushing supporting the rear shaft of the 3rd auger assembly. This zerk is located on the left rear corner of the tank above the inner cross brace. L14 Maintain the lube level in the (2) spinner gearboxes at 3/4 full. Check regularly for any observable leakage. If leakage is excessive, replace required in- ON CORNER OF FRAME put/output shaft seals. Lubricate with Semi-Fluid, EP Lithium Base, Gear Grease. L15 Clean and repack the wheel hubs with axle grease annually. Grease hub through zerk in hub monthly. Be careful not to over grease and force seal out of back side of hub. L16 L17 Oil slides on front idler tightener assembly. Grease (4) material guide pin sleeves. (2) located on each side of the spreader. L18 Grease (2) T-post hold down sleeve zerks located above the cross channel on the underside of the spreader. A zerk is located on the front and one on the rear of the sleeve. (SHIELDS REMOVED FOR ILLUSTRATIVE PURPOSES ONLY.) ON CORNER OF FRAME Model 8720/8865 -21 REPAIR PARTS 918-0308 (STANDARD 8720) (OPTIONAL 8865) (SERIAL #SI078720288-SI088720425) (FOR EARLIER MODELS SEE PAGE 24.) 918-0408 (STANDARD 8720) (OPTIONAL 8865) (SERIAL #SI088720426 & LATER) PTO DRIVE SHAFT-STAR PROFILE 1000 RPM 1-3/8 21 SPLINE WWE2480 (80 DEGREE C.V.) Model 8720/8865 -22 918-0308 (STANDARD 8720) (OPTIONAL 8865) (SERIAL #SI078720288-SI088720425) (FOR EARLIER MODELS SEE PAGE 24.) 918-0408 (STANDARD 8720) (OPTIONAL 8865) (SERIAL #SI088720426 & LATER) PTO DRIVE SHAFT-STAR PROFILE 1000 RPM 1-3/8 21 SPLINE WWE2480 (80 DEGREE C.V.) KEY PART NO. DESCRIPTION 1 918-0208-1-1 Yoke 1-3/8"-21 Splined Assembly 2 918-0208-1-3 Double Yoke 3 918-0208-1-2 Grease Zerk in Item 2 & 8 4 918-0308-1-1 Inboard Yoke 5 918-0208-1-5 Cross and Bearing Kit 6 918-0208-1-6 Spring Pin 10 x 80 7 918-0308-1-2 Profile S5 and Sleeve Welded Assy. 8 918-0308-2-1 Overrunning Clutch & S4LGA Profile Assy. 9 918-0308-2-2 Cut Out Clutch (Prior to serial #SI088720425) 918-0410-2-1 Cut Out Clutch (Serial #SI088720426 & Later) 10 918-0208-2-1 Cross and Bearing Kit 11 918-0208-2-4 Bearing Ring SC25 12 918-0308-2-3 Outer Shield Tube OVL 13 918-0308-2-4 Inner Shield Tube Round 14 918-0308-1-3 CV Cone and Bearing Assy. 15 918-0308-1-4 Shield Cone 3-Rib 16 918-0308-2-5 Shield Cone 8-Rib 17 918-0208-2-9 Screw-In Item 14,15 & 16 KEY PART NO. DESCRIPTION 18 918-0208-1-11 Support Bearing 19 918-0208-2-7 Safety Chain 20 918-0208-2-8 Decal Outer-In Item 12 21 918-0208-1-10 Decal Inner-In Item 7 22 918-0208-1-12 Zerk-In Item 7 23 918-0308-2-6 Lubrication Decal 24 918-0208-1-13 Cross and Bearing Kit 25 918-0208-2-10 Decal-K64 26 918-0208-1-1-1 Assembly Collar Kit (Inc. Ring, Collar & Balls) 27 918-0208-2-3-1 Clamp Cone Locking Pin (Prior to serial #SI088720425) 918-0410-2-1-1 Clamp Cone Locking Pin (Serial #SI088720426 & Later) 28 918-0308-1 1-3/8-21 Spline Tractor Half Assy. 29 918-0308-2 1000 RPM Implement . Assy. (Prior to serial #SI088720425) 918-0410-2 1000 RPM Implement . Assy. (Serial #SI088720426 & Later) KEY PART NO. DESCRIPTION 1 918-0308-2-2-1 Housing 2 918-0308-2-2-2 Hub (Prior to serial #SI088720425) 618-0003-2-1 Hub (Serial #SI088720426 & Later) 3 918-0308-2-2-3 Spring Pack 4 918-0208-2-3-5 Washer 5 918-0208-2-3-6 Retaining Ring 6 918-0208-2-3-7 Sealing Ring 7 918-0208-2-3-1 Clamp Cone Locking Pin (Prior to serial #SI088720425) 918-0410-2-1-1 Clamp Cone Locking Pin (Serial #SI088720426 & Later) 8 918-0308-2-2-4 Cam NS 918-0208-2-3-9 Bushing-In Item #2 NS 918-0208-2-3-11 Shim Kit Model 8720/8865 -23 Model 8720/8865 -24- 918-0208 PTO DRIVE SHAFT ASSEMBLY 1000 RPM-21 SPLINE / 1-3/8” YOKE WWE2480 (80 DEGREE C.V.) USED PRIOR TO SERIAL #SI078720287. FOR LATER MODELS SEE PAGE 22. 918-0208 PTO DRIVE SHAFT ASSEMBLY 1000 RPM-21 SPLINE / 1-3/8” YOKE WWE2480 (80 DEGREE C.V.) KEY PART NO. DESCRIPTION 1 918-0208-1-1 Yoke 1-3/8"-21 Splined Assembly 2 918-0208-1-2 Grease Zerk in item 3 3 918-0208-1-3 Double Yoke 4 918-0208-1-4 Inboard Yoke 5 918-0208-1-5 Cross and Bearing Kit 6 918-0208-1-6 Spring Pin 10 x 80 7 918-0208-2-1 Cross and Bearing Kit 8 918-0208-1-14 Profile and Sleeve Wa 9 918-0208-2-2 Overrunning Clutch & 1bGA Profile Assy. 10 918-0208-2-3-1 Clamping Cone Bolt (Included in Item 11) 11 918-0208-2-3 Cut Out Clutch 12 918-0208-2-4 Bearing Ring SC25 13 918-0208-2-5 Outer Shield Tube OVL 14 918-0208-1-7 Inner shield Tube Round 15 918-0208-1-8 CV Cone & Bearing Assy. 16 918-0208-1-9 Shield Cone 3 Rib 17 918-0208-2-6 Shield Cone 8 Rib KEY PART NO. DESCRIPTION 18 918-0208-2-7 Safety Chain 19 918-0208-2-8 Decal Out-In Item 13 20 918-0208-1-10 Decal In-In Item 8 21 918-0208-2-9 Screw-In Item 15,16 & 17 22 918-0208-...
Otros modelos de este manual:Herramientas de jardín - 8720 (2.76 mb)