Votos - 3, Puntuación media: 5
(
)
)
|
Resumen del manual
• Transport with clean reflectors, SMV and working lights as required by federal, state, and local laws. M100 WARNING 540 RPM SPEED RANGE ONLY HIGHER PTO SPEEDS CAN CAUSE PERSONAL INJURY AND EQUIPMENT FAILURE 101101 REMEMBER: If Safety Signs have been damaged, removed, become illegible or parts replaced without Signs, new Safety Signs must be applied. New Safety Signs are available from your authorized distributor or factory. 16 INSTRUCTIONS TRACTOR REQUIREMENTS AND PREPARATION The models SDM40-48, SDM40-Standard Duty Cutters require a Category tractor of at least 20 horsepower or and equipped with a 540 rpm PTO (power takeoff) in good working condition. It is recommended that only tractors with wide axles be used with this cutter. Tricycle front wheel arrangements are inherently unstable and tractor roll-over accidents are more likely to occur. The tractor also needs lift arm stabilizer bars or sway blocks to control side movement of the cutter. Check the tractor’s 3-pt. hydraulic lift system. Refer to your tractor operator’s manual or dealer for any adjustments necessary to put the hydraulic system in good working order. (I&T shop manuals will list most specifications and adjustment instructions - available from most farm equipment dealers.) Be sure tires and rims are in good condition. Inflate tires to the proper recommended air pressure. All tractors that are not equipped with a “live” power takeoff (PTO) need to be equipped with an over-running PTO clutch attachment. A special driveline assembly with an over-running clutch incorporated is available as an option (see optional equipment list). Check the tractor master shield over the PTO stub shaft. Make sure it is in good condition and fastened securely to the tractor. Purchase a new shield if old shield is damaged or missing. (You may have to use a tractor salvage yard for replacement parts on older tractors.) It is recommended that a ROPS (Roll-Over Protection Structure) and a seat belt be installed on all tractors. Contact your local dealer for a ROPS for your tractor. W ARNING! When using the unit, a minimum equipment weight must be on Without this weight, tractor could possible loss of control and possible or death. The weight may be attained with a front end loader, front wheel weights, ballast in tires or front tractor weights. When attaining a minimum 20% of tractor and equipment weight on the wheels, you must not exceed the ROPS weight certification. Weigh the tractor and equipment. DO NOT GUESS OR ESTIMATE! Figure 1. Tractor Stability W ARNING! A heavy load can cause instability in driving a tractor. Make sure the front of the tractor is properly counterbalanced with weights. Always drive slowly – especially around turns. An unstable tractor could steer badly and possibly tip over, causing injury or death. CAUTION! Be sure your tractor is in good condition. Read all the safety precautions and make sure all tractor operators are familiar with the safety rules of operation. The operator is responsible for the safe operation of this cutter. The operator must be properly trained. Operators should be familiar with the cutter and tractor and all safety practices before starting operation. Read the safety rules and safety signs on pages 4-16. This standard duty cutter is designed for grass and weed mowing and shredding. Recommended mowing speed for most conditions is from two to five mph. DANGER! FOR AGRICULTURAL USE ONLY! When this equipment is operated in populated areas or other areas where thrown objects could injure persons or property, full chain or rubber shielding (which is designed to reduce the possibility of thrown objects) must be installed. If this machine is not equipped with full chain or rubber shielding, operation must be stopped when anyone comes within several hundred feet. SAFETY . . . YOU CAN LIVE WITH IT! 17 INSTRUCTIONS ( continued) In some cases it will assembly to match your The following procedure should be used: 1. Raise the tractor 3-pt. hitch so cutter gearbox is in line with the shaft on the tractor. Shut down tractor, leaving cutter in position of shortest distance between shafts. SECURELY BLOCK CUTTER IN POSITION. 2. Pull driveline apart. Attach outer (female) section to tractor PTO shaft. Pull on driveline section to be sure that yoke locks into place. 3. Hold driveline sections parallel to each other to determine if too long. Each section should end approximately 3” (76mm) short of reaching universal joint shield on opposite section. If too long, measure 3” (76mm) back from universal joint shield and mark on opposite section (Figure 3). Do this for both sections. DO NOT CUT UNTIL STEPS 4 AND 5 ARE CHECKED. Figure 2. NOTE: The use of a PTO over-running clutch or extension could require that the PTO driveline be shortened a considerable amount. If this is done, the driveline halves may separate when the cutter is lowered to the ground or when operated on rough ground. An optional special driveline that is equipped with...
Otros modelos de este manual:Herramientas de jardín - SDM40-60 (350.32 kb)
Herramientas de jardín - SDM40-72 (350.32 kb)