Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Wash spreader after each use. Lubricate axle bearings with light oil. Store in a dry place. Questions, Comments, Information Call the toll-free Scotts Consumer Helpline: 1.800.543.TURFor visit Scotts No-Quibble Guarantee ® If for any reason you, the consumer, are not satisfied after using this product, you are entitled to get your money back. Simply send us proof of purchase and we will mail you a refund check promptly. The Scotts Company 14111 Scottslawn Rd. Marysville, Ohio 43041 Dedicated ToA Beautiful World ™ Trusted by generations of homeowners, Scotts isdedicated to helping you enhance and protect thenatural beauty of your home environment. ® © 2003, Licensed by The Scotts Company. World rights reserved. 03-AG1000 Printed in USAP/N: 735307-001 125030423 Instructions for Assembly and Use Thank you for purchasing a Scotts ® AccuGreen ® 1000 ™ Drop Spreader! The Scotts Company was first to market a spreader for home lawns, back in 1946. Today, Scotts continues to improve its entire line of spreaders, to make them more accurate, easy to use, more durable and longer lasting. The Scotts Difference ® U-shaped handle with handle mounted on/off control18-inch (46cm) spread width, for fast, easy coverageHolds 5,000 sq. ft. (470 sq. meters) of Scotts fertilizerDurable, rustproof plastic parts12-inch (30cm) wheels provide stability and maneuverabilityFolds for easy storageBacked by Scotts No-Quibble Guarantee ® Made in the U.S.A. 231 How to Apply Product For best results, follow the Scotts ® Annual Lawn Care Program™, and for seeding projects use Scotts ® Pure Premium ® Grass Seed. Set Rate Find the rate setting for "Scotts Drop Spreader" found on the back of the Scotts product package. Turn the micrometer until that number appears in the micrometer window. Fill Hopper With the spreader hopper closed (trigger control away from handle), fill the spreader over a patch of bare ground or driveway/sidewalk. DO NOT fill spreader on the lawn. Sweep up any spilled product. Apply Start walking, then squeeze and hold trigger to release product. Application TipsFor rectangular lawns, apply two header strips at each end of the lawn and then go backand forth. For irregular-shaped lawns, apply one headerstrip around the entire lawn, and then go back and forth. To avoid streaks or misses, slightly overlap each strip over the edge of the previous strip. Line up the arrow on the hopper with the wheel track from the previous row. ArrowWheel tracks from previous row Do not use wheel for alignment. ACCUGREEN 10 0 0 73445 PROOF OF PURCHASE 0 32247 73445 5 Handle Assembly Micrometer Housing Micrometer Barrel Bolt, 4 ea.* Frame Leg, 2 ea. Thumbnut, 4 ea.* Hopper Assembly Wheel, 2 ea. Axle Washer, 2 ea.* Cotter Pin, 2 ea.* Hubcap, 2 ea. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Parts List *Furnished in Hardware Kit How to Assemble Your AccuGreen® 1000™ Check to see if you have all parts shown below. Do not completely tighten nuts until the spreader assembly is complete. Frame Legs Insert frame legs (5) into the hopper assembly (7) slots. Attach legs to hopper, inserting bolts (4) through hopper then leg. Fasten legs in place with thumbnuts (6) on outside of hopper. Handle Attach handle assembly (1) using bolts and thumbnuts. Micrometer window must face the front of the spreader, thumbnuts face inside. Wheels Slide wheels (8) onto axle with the hub facing out. Slide axle washers (9) onto axle. Slip cotter pins (10) through axle holes and bend the ends around the axle. Align hubcaps (11) and snap into place. Micrometer Wire Screw micrometer barrel (3) into the micrometer housing (2). Tighten handle assembly and all other nuts. 1 2 3 4 Micrometer Window 1 3 4 2 5 6 7 8 9 10 11 Hopper Slot How to Calibrate the Spreader IT IS NECESSARY TO CALIBRATE YOUR SPREADER AFTER ASSEMBLING IT OR IT MAY SPREAD THE INCORRECT AMOUNT OF PRODUCT. Set Micrometer Turn micrometer until 6 is centered in window. Check Shutoff Bar Adjust Calibration Screw If the shutoff bar covers the calibration line, turn the adjustment screw counter-clockwise. If the bar is below the line, turn the adjustment screw clockwise. 1 2 3 4 Position Spreader Stand the spreader on its handle with the Scotts logo facing away from you. Press gently with your foot on the control lever and observe the position of the shutoff bar. Calibration screw Calibration line Shutoff bar With your foot on the control lever, the front edge of the shutoff bar at bottom of hopper should line up with the calibration line engraved into the bottom of the hopper. You may need to pull the shutoff bar towards you to see the calibration line. 6 6 centered in window ...