Votos - 4, Puntuación media: 3.3
(
)
)
|
Resumen del manual
Make sure everyone is clear of machinery before starting the engine, engaging power, or operating the machine. EMPLOYEE TRACTOR OPERATING INSTRUCTIONS: 1. Securely fasten your seat belt if the tractor has a 5. Watch where you are going, especially at row ROPS. ends, on roads, and around trees. 2. Where possible, avoid operating the tractor near 6. Do not permit others to ride. ditches, embankments, and holes. 7. Operate the tractor smoothly - no jerky turns, 3. Reduce speed when turning, crossing slopes, and starts, or stops. on rough, slick, or muddy surfaces. 8. Hitch only to the drawbar and hitch points recom- 4. Stay off slopes too steep for safe operation. mended by tractor manufacturers. 9. When tractor is stopped, set brakes securely and use park lock if available. Child Labor Under 16 Years Old Some regulations specify that no one under the age of 16 may operate power machinery. It is your responsibility to know what these regulations are in your own area or situation. (Refer to U.S. Dept. of Labor, Employment Standard Administration, Wage & Home Division, Child Labor Bulletin #102.) 5 SECTION l INTRODUCTION AND DESCRIPTION 1-1 INTRODUCTION We are pleased to have you as a Bush Hog customer. Your Bush Hog Rotary Tiller has been carefully designed to give maximum service with minimum down time. This manual is provided to give you the necessary operating and maintenance instructions for keeping your rotary tiller in top operating condi- tion. Please read this manual thoroughly. Understand what each control is for and how to use it. Observe all safety precautions decaled on the machine and noted throughout the manual for safe operation of the implement. If any assistance or addi- tional information is needed, contact your authorized Bush Hog dealer. NOTE All references made in this manual to right, left, front, rear, top and bottom is as viewed facing the direction of forward travel with implement properly attached to tractor. 1-2 DESCRIPTION The RTC series of rotary tillers are intended for light duty use in an environment relatively clean of for- eign objects such as large rocks, etc. Each tiller is equipped with adjustable skid shoes and rear deflec- tor shield for setting the desired operating depth and tilth of soil. The drivetrain consists of a telescoping input driveshaft; 90 degree transfer gearbox, cross- shaft and chain drive rotor. Protection is provided by a slip clutch on the driveline. The chain is self- adjusted by a spring tension device. Major compo- nents are identified in Figure 1-1. A-FrameChain Drive Cover(Behind End Plate) RearDeflectorAdjustable Skid ShoeParking StandRotor/Blade AssemblyDriveline With Slip ClutchInput GearboxFigure 1-1 Major Components 6 Minimum Overlap SPECIFICATIONS Tilling width Overall width Offset Blades per flange No. of flanges Hitch PTO speed Rotor speed Max. recommended HP Max. till depth Gearbox oil capacity Weight Driveline protection Model RTC40 Model RTC48 39-1/4” 48-1/4” 44” 53” 4” N/A 4 4 4 5 3-point Cat. I only 540 rpm 250 rpm 24 6” 17 ozs. 308 lbs. 335 lbs. Slip Clutch SECTION II PREPARATION FOR USE 2-1 ATTACHING TO TRACTOR Figure 2-1 WARNING TO AVOID SERIOUS INJURY OR DEATH: NEVER STAND BETWEEN TRACTOR AND TILLER WHILE TRACTOR IS BEING BACKED TO HITCH. WARNING TO AVOID SERIOUS INJURY OR DEATH: ADDITIONAL TRACTOR FRONT BAL- LAST MAY BE NEEDED FOR STABLE OPERATION AND TRANSPORT OF THE TILLER. SEE TRACTOR OPERATOR’S MANUAL FOR RECOMMENDED WEIGHTS. A. Attach tiller to tractor 3-point hitch per tractor operator’s manual. Do not attach driveline at this time. NOTE Due to the many variations in tractor/implement hitch points and corresponding differences in distances between tractor PTO shafts and implement input shafts, drivelines may need to be shortened as described in the following steps: B. Raise and lower tiller to determine position with shortest distance between the tractor PTO shaft and gearbox input shaft. Shut down tractor, leaving tiller in position of shortest distance. Securely block tiller in position. C. Pull driveline apart. Attach outer (female) sec- tion to tractor PTO shaft. Pull on driveline section to be sure that yoke locks into place. D. Hold driveline sections parallel to each other to determine if it is too long. Each section should end approximately 3 inches (76mm) short of reaching universal joint shield on opposite section. If too long, measure 3 inches back from universal joint shield and mark on opposite section. (Figure 2-1). Do this for both sections. E. Raise and lower tiller to determine position with greatest distance between PTO shaft and gear- box input shaft. Shut down tractor leaving tiller in position of greatest distance. Securely block tiller in position. F. Hold driveline sections parallel to each other and check for minimum 6 inches (15cm) overlap. (Figure 2-2) If driveline has been marked for cutting, overlap will be the distance between two marks. If driveline has less than minimum overlap, do not use. Cont...
Otros modelos de este manual:Herramientas de jardín - RTC (613.3 kb)
Herramientas de jardín - RTC (613.3 kb)