Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
Remove the clip and the stop ring from the stem of the thermostatic mixer. Turn the water on to the handshower. Turn the temperature control stem until the output water is the desired maximum high temperature -- usually 110o*. Turn the water off. Replace the stop ring so that the tooth is against the high temperature limit stop. Replace the clip. Justify the handle. *Please know and follow all applicable local plumbing codes when setting the high temperature limit stop. User Instructions Using the Thermostatic Mixer Turn the handle clockwise to make the water cooler. Turn the handle counter-clockwise to make the water warmer. When the safety stop override is at the 12:00 position, the output water is 100o F, the handle will stop. If a user wants water hotter than 100o F, press the safety stop override button and continue turning the handle counter-clockwise. Using the Diverter Pull the lever upward to turn the water on. Pivot the handle to the desired function. There are five functions: Alll-around shower (handshower and 4 lower bodysprays) 4 lower bodysprays 2 upper bodysprays Full-body massage (all 6 bodysprays) Handheld shower Using the 3-Jet Handshower To change spray modes, push the selector lever until the desired spray is achieved. selector lever Rain AIR Balance AIR Whirl AIR Scale Removal The Raindance Air 3-jet handshower incorporates the RubitTM cleaning system. If scale deposits are noticed in the spray channels, turn the water on lightly and rub the spray channels with a finger or a sponge. If scale deposits are noticed on the spray face, pour about 3/4” of a commercial scale remover, such as Lime-AwayTM or CLRTM ,into a shallow dish. Dilute the scale remover according to the label instructions. Soak only the spray face in the solution for the amount of time specified on the label. Rinse the handshower with clear water. Reinstall the handshower. Turn on the water and allow the handshower to flush for at least one minute. Troubleshooting Problem Possible Cause Remedy Insufficient water - Supply pressure inadequate - Filters on thermostat cartridge dirty - Screen washer dirty - Check water pressure (If a pump has been installed, check to see if the pump is working). - Clean thermostat filters - Clean screen washer between shower and hose Crossflow, hot water being forced into cold water pipe, or vice versa, when mixer is closed - Check valves dirty or leaking - Clean check valves, replace if necessary Output temperature does not correspond with temperature set - Handle not justified - Hot water temperature too low - Justify handle - Reset high temperature limit stop Temperature regulation not possible - Temperature regulator dirty or calcified - Panel is cross-connected - Clean temperature regulator, replace if necessary - Connect supply hoses to correct supplies Safety stop override button not operating - Spring defective - Button calcified - Clean spring and/or button, replace if necessary Diverter control stiff - Diverter cartridge defective or dirty - Replace cartridge 4 2 1 3 5 20 6 21 22 13 12 18 11 23x2 29x2,5 25x2 10 16 6 17 15 14 8 6 9 7 19 Replacement Parts 1 handshower 28519XXX 2 slider 97024XXX 3 handshower hose, 63” 28276XXX 4 upper cover 97324000 5 escutcheon 97326000 6 body shower 28406000 7 diverter handle 10490XXX 8 thermostatic mixer handle 38391XXX 9 flange 97858XXX 10 front cover 97859000 11 sleeve 95032XXX 12 adapter for handle 97108000 13 thermostat cartridge 94282000 14 nut 96945000 15 diverter cartridge 96645000 16 sealing set 95037000 17 connection hose 13099001 18 fixing set for hose connection 9415...
Otros modelos de este manual:Fontanería - Raindance S 27005XX1 (5.29 mb)
Fontanería - Raindance S 27005XX1 (5.29 mb)
Fontanería - Raindance S 27005XX1 (5.29 mb)