Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Unplug the power cord from the electrical outlet. 2. Close the main water supply valve. 3. Pull the product forwards by holding both sides of the product while pressing the button at the bottom left of the product, to separate the product from the installation plate. Unplug the product if it will not be used for a long time. Tips .... 4. Remove the drain plug at the back of the bidet by turning it counterclockwise by 90 degrees . and then pulling it forwards . so that the water in the hot water tank is drained into the toilet. Cleaning the MESH filter 1. Separate the product from the installation plate. - Refer to Removing the product (1~3). 2. Remove the MESH filter at the bottom left of the product. - Remove the MESH filter by turning it with a ‘+’ screw driver. Cleaning and maintaining your bidet Cleaning the MESH filter 3. Clean the MESH filter by shaking it under flowing water. - Removing foreign substances from the MESH filter with a toothbrush is more effective. - Do not clean the MESH filter excessively, as it may damage the MESH. 4. Reinstall the cleaned MESH filter into the product. - Check that the MESH filter is installed correctly. - If you open the main water supply valve when the MESH filter is not completely installed, water leakage may occur. When not using the product for a long period of time, clean the filter before using the product again. The filter cleaning interval may differ depending on the water quality. Tips 23 SPECIFICATIONS Product name Coway Bidet Model no. BA13-AR/AE/BR/BE Standard power voltage 120 V~ 60 Hz Power consumption 1 200 W Supply water pressure 0.11 MPa - 0.68 MPa Dimensions BA13-AR/BR 382 mm (Width) . 493 mm (Depth) . 144 mm (Height) BA13-AE/BE 382 mm (Width) . 528 mm (Depth) . 144 mm (Height) Weight 6 kg - 6.5 kg Warm water cleansing device Rear cleansing Maximum 0.5 L/min, automatic nozzle self-cleaning function Front cleansing Maximum 0.5 L/min, automatic nozzle self-cleaning function Standard time Rear cleansing 1 minute, front cleansing 1 minute, drying 2 minutes Water pressure control 3 levels Micom control Warm water temperature control 4 levels (Off : Room temperature, L : 31.5 ., M : 34.5 ., H : 37.5 .) Power consumption by heater 1 250 W Safety devices Bimetal, temperature sensor, temperature fuse (overheating prevention), micro switch Air dryer device Warm air temperature control 4 levels (Off : Room temperature, L, M, H) Standard time Drying for 2 minutes Power consumption by heater 180 W Safety devices Bimetal, temperature fuse (overheating prevention) Heated seat Seat temperature control 4 levels (Off : Room temperature, L : 31 ., M : 34 ., H : 37 .) Power consumption by heater 60 W Safety devices Bimetal, temperature fuse (overheating prevention) MESH filter Specifications 25.2 mm (Length) . 19.8 mm (O) Installation parts T-shaped connector, Bidet hose, Installation plate, 2 fixing screws, 2 fixing rubbers, 2 fixing washers, 2 fixing nuts, 2 fixing sliders, 2 screws, 2 anchors, 3 batteries (AAA), Remote control wall mount Other functions Instant warm water system, AIR+water stream, MESH filter, Eco mode, Stainless steel twin nozzle (The Wide, Deodorization and Sterilization functions are supported for the BA13-BR/BE only) Operating temperature 0 . - 40 . Manufacturer: Woongjin Cuchen Co., Ltd. The specifications are subject to change without prior notice for reasons of improving the product performance. 24 TROUBLESHOOTING The bidet may operate abnormally due to minor causes not because of a product malfunction but because the user is unfamiliar with using the product. In such a case, problems can be easily solved even without the help of the Service Center by checking the following. If you cannot solve the problem after checking the following items, please call the Service Center. PROBLEM SOLUTION The product is not working. • Make sure the bidet is plugged in. • Check if there was a power failure. • Check if the remote control batteries are flat. Replace them if necessary. No water is ejected. • Make sure the water valve is opened. • Clean foreign material from the nozzle outlet holes using a toothbrush. • Make sure the water supply is running. The water pressure is weak. • Make sure that the water pressure is not too low. • Clean foreign material from the nozzle outlet hole using a toothbrush. • Remove, clean and then reinstall the filter (refer to p.21) The seat or the water is not warm. • Make sure that the seat and water temperature control buttons are set to the ‘ON’ status. Please adjust the setting to the correct temperature by pressing the seat temperatre button or the water temperature button. • This bidet has a bimetal as one of safety device for water heater. The safety device may cycle ‘OFF’ if temperature exceeds over normal level. In the event of the safety device operation, the bidet do not work and show error message until the appliance cool down and then the bimetal will automatically reset. If the error message shows up, you can r...
Otros modelos de este manual:Fontanería - BA13-BE (3.07 mb)
Fontanería - BA13-AR (3.07 mb)
Fontanería - BA13-AE (3.07 mb)