Iniciar sesión:
Votos - 3, Puntuación media: 4.3 ( )

Manual de usuario Axor, modelo TROPIC CADET 2492

Fabricar: Axor
Tamaño del archivo: 140.15 kb
Nombre del archivo:
Idioma del manual:
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


Secure with metal washer/nut combo. b. With tank parallel to wall, alternately tighten nuts until tank is snugged down evenly against bowl surface. CLOSET FLANGE CLOSET BOLT NUTWASHER BOLT CAP WASHER/ NUT COMBO ! ! CAUTION: DO NOT OVERTIGHTEN NUTS MORE THAN REQUIRED FOR A SNUG FIT! For Tanks/Bowls using Speed Connect System (Tank mounting bolts pre-installed). USE INCLUDED TOOL, NUT DRIVER, OR DEEP SOCKET RACHET.* 6 7 INSTALL TOILET a. Position toilet squarely to wall and, with a rocking motion, press bowl down fully on wax ring and flange. Alternately tighten nuts until toilet is firmly seated on floor. CAUTION: DO NOT OVERTIGHTEN NUTS OR BASE MAY BE DAMAGED! b. Install caps on washers. (If necessary, cut bolt height to size before installing caps.) c. Smooth off the bead of sealant around base. Remove excess sealant. INSTALL TANK a. Install large rubber gasket over threaded outlet on bottom of tank and lower tank onto bowl so that tapered end of gasket fits evenly into bowl water inlet opening, and tank mounting bolts go through mounting holes. Secure with metal washer/nut combo. b. With tank parallel to wall, alternately tighten nuts until tank is snugged down evenly against bowl surface. CLOSET FLANGE CLOSET BOLT NUTWASHER BOLT CAP WASHER/ NUT COMBO ! ! CAUTION: DO NOT OVERTIGHTEN NUTS MORE THAN REQUIRED FOR A SNUG FIT! For Tanks/Bowls using Speed Connect System (Tank mounting bolts pre-installed). USE INCLUDED TOOL, NUT DRIVER, OR DEEP SOCKET RACHET.* 8 INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions. 9a 9bBefore continuing, determine the type of water supply connecation you have from the chart below and use the appropriate assembly parts required to properly reconnect the water supply. DO NOT use plumber's putty to seal these fittings. CAUTION: DO NOT USE CONE WASHER WITH PLASTIC SUPPLY LINE. These parts must be used as illustrated to insure water-tight connection. Use of existing coupling nut may result in water leakage. Water supply tube or pipe must extend at least 1/2" inside threaded shank of valve (does not apply to flanged tubing). Use existing coupling nut and washer. Use existing spiral cone washer. Fluidmaster cone washer may not seal completely on spiral type supply line. Captive cone washers already included. No additional washers needed. CAUTION: Overtightening of LOCK NUT or COUPLING NUT could result in breakage and potential flooding. METAL / COPPER FLARED TUBING METAL FLANGED TUBING METAL SPIRAL TUBING VINYL / BRAIDED CONNECTOR LOCK NUT LOCK NUT LOCK NUT LOCK NUT COUPLING NUT COUPLING NUT EXISTING COUPLING NUT COUPLING NUT WATER SHUT-OFF WATER SHUT-OFF WATER SHUT-OFF WATER SHUT-OFF CONE WASHER EXISTING CONE WASHER EXISTING WASHER With correct washers in place (see Step 9a), tighten COUPLING NUT 1/4 turn beyond hand tight. DO NOT OVERTIGHTEN. ! WARNING: Do not use plumber’s putty, pipe dope, or any other sealant on the water supp...

Otros modelos de este manual:
Fontanería - TROPIC CADET 2492 (140.15 kb)
Fontanería - TROPIC CADET 2455 (140.15 kb)
Fontanería - TROPIC CADET 2490 (140.15 kb)
Fontanería - TROPIC CADET 2455 (140.15 kb)

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría