Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
9A Turn on water supply. Submerge the FLOAT CUP under the water for 30 seconds. Adjust the water to desired level by turning WATER LEVEL ADJUSTMENT ROD and moving FLOAT CUP up or down. NEW SAVONA ONE-PIECE TOILET REPAIR PARTS LIST NOTE: "XXX" represents color options. Specify when ordering.TRIP LEVER TANK COVER BOLT CAPS SEAT POST MTG. KIT SEAT AND COVER (INCLUDES MTG. KIT) FLAPPER ASSEMBLY FLUSH VALVE FLUIDMASTER WATER CONTROL DESCRIPTIONCOMPONENT 1.6 GPF Tank Cover Seat - Elongated Bolt Cap Kit Cover Trip Lever - Right Hand Inlet Valve Flush Valve - 1.6 GPF Flapper Assembly - 1.6 GPF 735146-400.XXX0A 5205.110.XXX 730835.XXX 7381059-200.XXX 738565-441.0070A 738942-1000A 738920-0070A v v v - v v v 7301387-100 9 10 ADJUSTMENTS a. Adjust water level. Water level should be adjusted to level indicated on tank by adjusting float cup. See Step 10 for water level adjustment method. b. If bowl fails to siphon, an adjustment may be required with the lift chain. Simply remove the bead chain from the retainment clip (see Fig. 9A) and take up slack on the chain, and reinsert on lift rod. Make sure the chain is not too taught. 11 - 3 - CARE AND CLEANING When cleaning your toilet, wash it with mild, soapy water, rinse thoroughly with clear water and dry with a soft cloth. Avoid detergents, disinfectants, or cleaning products in aerosol cans. NEVER use abrasive scouring powders or abrasive pads on your toilet seat. Some bathroom chemicals and cosmetics may damage the seat's finish. WARNING: Do not use in-tank cleaners. Products containing chlorine (calcium hypochlorite) can seriously damage fittings in the tank. This damage can cause leakage and property damage. American Standard shall not be responsible or liable for any tank fitting damage caused by the use of cleaners containing chlorine (calcium hypochlorite). ! TANK LEVER "S" CLIP FLUSH VALVE TOP ARM NIPPLE Diagram 1 PARTS FOR WATER CONNECTION (SEE STEP 9) CONE WASHER VALVE BODY FLAPPER THREADED SHANK SHANK WASHER COUPLING NUT (HAND TIGHT ONLY) FILL VALVE FLOAT CUP CRITICAL LEVEL MARK ("C.L.") MUST BE 1" ABOVE OVERFLOW PIPE REFILL TUBE ADJUSTABLE HEIGHT WATER LEVEL ADJUSTMENT ROD LOCK NUT Fig. 9A Turn on water supply. Submerge the FLOAT CUP under the water for 30 seconds. Adjust the water to desired level by turning WATER LEVEL ADJUSTMENT ROD and moving FLOAT CUP up or down. NEW SAVONA ONE-PIECE TOILET REPAIR PARTS LIST NOTE: "XXX" represents color options. Specify when ordering.TRIP LEVER TANK COVER BOLT CAPS SEAT POST MTG. KIT SEAT AND COVER (INCLUDES MTG. KIT) FLAPPER ASSEMBLY FLUSH VALVE FLUIDMASTER WATER CONTROL DESCRIPTIONCOMPONENT 1.6 GPF Tank Cover Seat - Elongated Bolt Cap Kit Cover Trip Lever - Right Hand Inlet Valve Flush Valve - 1.6 GPF Flapper Assembly - 1.6 GPF 735146-400.XXX0A 5205.110.XXX 730835.XXX 7381059-200.XXX 738565-441.0070A 738942-1000A 738920-0070A v v v - v v v 12 • Make sure water supply is off. Remove valve TOP by lifting arm and rotating top and arm 1/8 turn counterclockwise, pressing down slightly on cap. IMPORTANT: Always clear sand and rust from system. • While holding a container over the uncapped VALVE to prevent splashing, turn water supply on and off a few times. Leave water supply off. • Replace TOP by engaging lugs and rotating 1/8 turn clockwise. MAKE CERTAIN TIP IS TURNED TO THE LOCKED POSITION. VALVE MAY NOT TURN ON IF TOP IS NOT FULLY TURNED TO THE LOCKED POSITION. For troubleshooting information please contact: TROUBLESHOOTING IF FILL VALVE SHUTS OFF BUT CONTINUES TO LEAK SLOWLY, repeat Step 12. IF FILL VALVE TURNS OFF AND ON DURING PERIODS OF NON-USE, it is a signal you are wasting water because: • The end of the refill tube is inserted into overflow pipe, below water level in tank. Attach refill tube to overflow pipe using "S" clip provided. • The flush valve is leaking because it's worn, dirty or misaligned with tank ball or flapper (replace with a new flapper). IF FILL VALVE WON'T TURN ON OR SHUT OFF or REFILL OF TANK WATER IS SLOW after valve has been in use for some time, Fluidmaster Model 242 Replacement Seal may be needed. Go to our website at for more solutions to toilet problems. © 2001 Fluidmaster, Inc. ® Registered trademark of Fluidmaster, Inc. GUARANTEE: This Fluidmaster product is guaranteed to be free from defective materials and workmanship for a period of one year. Units returned to Fluidmaster will be replaced without charge. Always use quality Fluidmaster repair parts when maintaining your Fluidmaster products. Fluidmaster shall not be responsible or liable for any damages caused by products used with Fluidmaster valves that were not manufactured by Fluidmaster, Inc. 30800 Rancho Viejo Road San Juan Capistrano, CA 92675 (949) 728-2000 (800) 631-2011 LEVER LE BRAS E...
Otros modelos de este manual:Fontanería - NEW SAVONA 2097.012 (169.05 kb)
Fontanería - NEW SAVONA 2097.012 (169.05 kb)
Fontanería - NEW SAVONA 2097.012 (169.05 kb)