Votos - 2, Puntuación media: 3.5 ( )

Fabricar: Bradley Smoker Tamaño del archivo: 227.87 kb Nombre del archivo: Idioma del manual:

Position sensor cable (2) through one of the rounded slots in the stilt washer (1). 1 2 5 If faucet was installed with cover plate, secure cover plate with basin washers (1), flat washers (2) and locknuts (3). 1 2 3 CAUTION: Flush water lines 7a before beginning this step. Attach the outlet assembly (1) and aerator gasket (2) to the spout. The outlet assembly is equipped from the factory with a 0.5 GPM cartridge (white screen). To configure the 2 outlet with the 2.2 GPM cartridge (yellow screen) refer to step 8. IMPORTANT: If 0.5 GPM spout is to be used, skip Step 8 and proceed 1 directly to Installation - Solenoid and Optional Valves, page 4. 1 4 3 2 2 Install faucet assembly into deck hole. Use plumbers putty to seal faucet to deck. Be careful not to nick or cut the sensor cable during installation. 4 Install the shank washer (1) and locknut (2) onto faucet shank. Tighten locknut securely to prevent collar and spout from rotating. If necessary, support spout base from above to prevent twisting. 1 2 6 Install spout nut (1) onto the spout. For swivel mount, only install two plastic split washers (2). 1 For rigid mount, only install 2 1/8" thick plastic washer (3). Mount the spout completely into the base and securely tighten the spout nut (1). 3 IMPORTANT: Flow rates exceeding the 7b 0.5 GPM maximum limit for public lavatories set by ASME A112.18.1 negate the UPC certification of this faucet for public use applications. For applications requiring laminar flow without an aerator, refer to the instructions below. Attach the plain spray ring (1) to the spout. Insert the laminar flow control insert (2) into the spout. IMPORTANT: If laminar flow is to be used, skip Step 8 and proceed directly to Solenoid and Optional Valves, page 4. 1 (269-1814) 2 (269-1815) 8 IMPORTANT: Flow rates exceeding the 0.5 GPM maximum limit for public lavatories set by ASME A112.18.1 negate the UPC certification of this faucet for public use applications. To convert outlet assembly to 2.2 GPM: 5 1.Disassemble outlet assembly using key (1). 2.Remove the 0.5 GPM cartridge (white screen) and replace it with the 4 2.2 GPM cartridge (2). 3 3.Install the rubber washer (3), adapter (4) and aerator gasket (5). 2 IMPORTANT: Proceed directly to Installation - Solenoid and Optional Valves, page 4. 1 Bradley Corporation •215-1559 Rev. A; EN 04-216A 9/23/04 Aerada 1000 Series Gooseneck Faucet Installation Instructions Installation Instructions - Solenoid Valves and Electronic Box (AC) Models S53-308 and S53-309 Thread the union nut (1) of the solenoid assembly to the faucet shank (2). Use Teflon tape on the threads to ensure a leak-free joint. Make sure the solenoid is positioned for easy access. Tighten the union nut. CAUTION: Do not use pipe dope on threads. The solenoid could become contaminated and will void any warranty. Remove the strain relief cover and screw (1) using hex key provided (2). Remove both foam gaskets (3). Separate the foam gaskets at the perforation. 1 2 1 3 2 CAUTION: Do not attempt to operate multiple faucets using a single transformer. Insert larger foam gasket (1). Attach strain relief cover (2) with screw (3) using hex key provided (4). 1 2 3 4 Re-attach the electronic box to the baseplate location using screw(1) and hex key provided (2). NOTE: To ensure the electronic box is level with or above the solenoid valve, the cables should create a drip loop. The electronic box is designed with the wire connectors facing downward to ensure proper drip loops. 2 1 2 When ...

Descargar ahora

Introduzca dos números de la imagen: