Votos - 3, Puntuación media: 3.3
(
)
)
|
Resumen del manual
RJ11 telephone cord 1 - Installation & driver CD with Fax, Voicemail and Modem-on-Hold software About This Product This 56К PCI internal modem allows you to connect to all dial-up Internet Service Providers, including AOL®, Earthlink™ and NetZero®. System Requirements One free PCI slot Intel® Pentium® II, Celeron®, AMD® Athlon® or Duron® class processor at 233MHz or faster 32MB System RAM CD-ROM drive Windows® 98 or later Linux® 2.4 Kernel or later Telephone line with dial tone Key Features • Plug-and-play compatibility • Fully compatible with V.90 and V.92 • V.44 compression for faster downloads The IC56A modem is built with the highest quality components and Is designed for reliability, compatibility, and performance. DO NOT RETURN THIS PRODUCT TO STORE. CONTACT STRATITEC AT 888.336.4418 FOR ASSISTANCE. MODEL # IC56A Manual v1.84 120705 Hardware Installation 1. Shut down your computer and open the computer case. 2. Insert the IC56A PCI card into an available PCI slot. 3. Make sure the card is firmly seated in the slot, then screw in the metal bracket at the back of the case and reassemble the computer case. Connect the Modem 1.Plug one end of the included telephone cord into a wall outlet and the other end into the modem port where indicated by the outlet symbol (or "Line"). 2. You may also connect your telephone through the modem by plugging one end of a standard RJ11 telephone cord into the modem port where indicated by the telephone symbol (or "Phone") and the other end into your telephone. Driver Installation Once the modem hardware is installed, turn on your computer and wait for the operating system to load. Once loaded, if you are prompted to restart your computer, please do so. Otherwise follow the instructions for your operating system. NOTE: Do not use the "Update Driver" feature from the Device Manager or Found New Hardware Wizard as the modem driver will not properly install. Windows 98/98SE 1. When the "Add New Hardware Wizard" screen appears, click 'Cancel.' 2. Browse to "D:\Driver\WIN98," (where "D" is the letter of your CD-ROM drive) and double-click 'setup' or 'setup.exe.' The correct setup file should be identified by a blue computer icon. 3. After the driver installation is complete, shut down (power off) your computer completely, wait 15-30 seconds and restart it. 4. Refer to the included Modem Installation Checklist to verify the modem is installed correctly. Windows ME 1. Windows ME will automatically install the drivers for a Lucent Win Modem. These drivers should be replaced with the drivers on the included CD for best results. 2. To replace the drivers installed by Windows ME, browse to "D:\Driver\WINME," (where "D" is the letter of your CD-ROM drive) and double-click "LTRemove.exe." You will be prompted whether or not you wish to continue, click "Yes." 3. When the remove function is complete you will be prompted whether or not you wish to restart now, click "No." (If you restart, Windows will re-install a Lucent Win Modem and you will have to return to step 2.) Browse to "D:\Driver\WINME," (where "D" is the letter of your CD-ROM drive) and double-click 'setup' or 'setup.exe.' The correct setup file should be identified by a blue computer icon. 4. After the driver installation is complete, shut down (power off) your computer completely, wait 15-30 seconds and restart it. 5. Refer to the included Modem Installation Checklist to verify the modem is installed correctly. Windows 2000 1. When the "Add New Hardware Wizard" screen appears, click 'Cancel.' 2. Browse to "D:\Driver\W2KXP," (where "D" is the letter of your CD-ROM drive) and double-click 'setup' or 'setup.exe.' The correct setup file should be identified by a blue computer icon. 3. After the driver installation is complete, shut down (power off) your computer completely, wait 15-30 seconds and restart it. 4. Refer to the included Modem Installation Checklist to verify the modem is installed correctly. Windows XP 1. Windows XP will automatically install the drivers for a Lucent Win Modem. These drivers should be replaced with the drivers on the included CD for best results. 2. To replace the drivers installed by Windows XP, browse to "D:\Driver\W2KXP," (where "D" is the letter of your CD-ROM drive) and double-click "LTREMOVE.exe." You will be prompted whether or not you wish to continue, click "Yes." 3. When the remove function is complete you will be prompted whether or not you wish to restart now, click "No." (If you restart, Windows will re-install a Lucent Win Modem and you will have to return to step 2.) Browse to "D:\Driver\W2KXP," (where "D" is the letter of your CD-ROM drive) and double-click 'setup' or 'setup.exe.' The correct setup file should be identified by a blue computer icon. 4. After the driver installation is complete, shut down (power off) your computer completely,...