Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
Click on the WPS Connect button. Step 2 Choose your configuration method, either Push Button or Pin Code and click Next. 31 Step 3a If you choose the Push Button method, make sure that you click on the Wi-Fi Protected Setup button. 32 Step 3b Push the WPS button on the router, and the blue LED will start blinking. The router will now start the handshake with the wireless adapter, then the connection will be built up in couple minutes. Step 4a If you choose the Pin Code method, write down the PIN and click Next. 33 Step 4b Log in to your router’s configuration page from the web browser and click on Wireless. Then click Wireless security. Make sure that the Wi-Fi Protected Setup Enable box is checked. Click the Add Wireless Device Wizard button. Step 4c Enter the Pin Code in the Pin Number box and click Connect. After a few moments both the router configuration screen and the adapter configuration screen should show a message telling you that you are connected. Step 4d Click Continue on the router configuration screen. 34 Step 5 Click Finish on the WPS Connection screen. Note: If you cannot connect successfully with WPS, you need to log in to your router’s configuration and click on Wireless. Then click Wireless security. Make sure that the Wi-Fi Protected Setup Enable box is checked. 35 4.7 About The About tab shows the Utility, Driver versions, and the MAC address of the adapter. 36 Appendix A – Features Frequency Band • 2.4~2.5 GHz Standards • IEEE 802.11b / 802.11g • 802.11n draft 2.0 Interface • PCI Antenna type • 3 external 2dBi antenna Security • WPA-PSK (TKIP) • WPA2-PSK (AES) Transmitted Power • 802.11b: 17 dBm • 802.11g: 14 dBm • Draft 11n: 14 dBm Data Rate • Transmitting: Up to 300Mbps* • Receiving: Up to 300Mbps* System Requirements • 150 MHz processor or better • 64 MB RAM • Available PCI slot LEDs • Activity • Power OS Compatibility • Windows 2000/XP/Vista Dimensions • 234 x 122 x 23 mm (L x W) Temperature • Operating: 0.C to 55.C • Storage: -20.C to 75.C Humidity • Operating: 10% to 80% Non- Condensing • Storage: 5% to 90% Non- Condensing Warranty • Limited 1-year warranty Safety Approvals • FCC, CE, IC 37 Appendix B – Information Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1 through 11. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 38 Industry Canada Statement This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: 1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device This device has been designed to operate with an antenna having a maximum gain of 2dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the EIRP is not more than required for successful communication. IMPORTANT NOTE: IC Radiation Exposure Statement: This equipment complies wit...