Votos - 4, Puntuación media: 3.5
(
)
)
|
Resumen del manual
For more advanced features such as configuring encryption settings, please refer to the User’s Manual on the provided CD. Note: Be sure to power off your computer before inserting the USB adapter. Step 1 Insert the USB adapter into an available USB port and turn on your computer. Step 2 After turning on the computer, Windows will launch the Found New Hardware Wizard. The Found New Hardware Wizard appears differently depending on your operating system. Click Cancel to quit the wizard and insert the Installation CD into your CD drive. Step 3 The Autorun screen will pop up. Select Install Utility and Driver from the menu. Note: If the Autorun screen doesn’t appear automatically go to Start, Run, and type D:\Utility\Setup.exe (where D is the letter of your CD drive) and click OK. Windows Vista users: At this point, Step 5 Click Next to accept the one below. Make sure that Allow to continue with Step 4 Click Next at the welcome screen. Step 6 Click Continue Anyway at the Windows Logo Screen. (For Windows 2000, click Yes at the Digital Signature Not Found prompt). For Windows Install this button when the security warning Step 8 After the computer will Update, select No, not this time and click Next. If this screen you can skip to section Step 7 Click Yes, I want to restart my computer now and then Finish to restart your computer. Step 9 Select Install the software automatically and click Next. Step 10 Click Continue Anyway at the Windows (For Windows Step 11 Click Finish. 2000, click Yes at the Digital Signature Section 2 For Windows Vista, click the Install this driver software anyway button when the security warning appears. Configuring the Wireless Adapter Note to Windows XP Users: You must disable the Wireless Zero Configuration Utility. Please follow the steps below to disable XP’s wireless utility. Windows Vista users can skip the following instructions and go to Step 1 Double-click on the Wireless Network Connection Icon in the system tray and then click on Properties or Advanced. When the new Step 2 Go to the AP List tab, select SSID (Network Name) Wireless Networks tab, uncheck Use Windows network you wish Connect. network settings check box and click OK. If the network you are attempting to connect to is configured for encryption, will see an orange lock icon next to the network. Step 1 To open the utility, double click on the Wireless Monitor icon in the system tray at the bottom right-hand corner of your screen. When you encryption key Enter the encryption OK. Step 3 You should now be connected. You should see “Connected” in the top, right hand corner, and there will be a blue circle around the antenna icon next to the network name. Section WiFi Protected Wi-Fi Protected Setup™ ( WPS) is a new and easy way to configure for your wireless network clients. In order to use it with your router, firstly, you must configure the wireless encryption You can find instructions for configuring it in the User Manual located on Secondly, you will need to have a wireless router router does not support WPS, you will need and you can skip this section. In the instructions below, we are going to use the Wireless Monitor, and the AirLink101 AR680W 300N wireless router configuration page as Step 1 Go to the computer with the Airlink101 300N wireless adapter and open the Wireless Monitor. Click on the WPS Connect button. Note: If you do not see the WPS Connect button, you can go to to download the latest utility and driver. Step 2 Choose your Push Button or Pin Code, and Step 3b If you choose Wi-Fi Protected click Next. button. Step 4 Go to your routers configuration screen and click on Wireless. Then click Step 3a Write down the PIN if you choose Pin Code method and click Next. Wireless security. Make sure that the Wi-Fi Protected Setup Enable box is checked. Then click the Add Wireless Device Wizard button. If you are using Pin Number box and click connect. If you are using Virtual Push Button or the physical push After a few moments both the router configuration screen and the adapter configuration screen should show a message telling you that you are connected. Step 5 Click Finish on the adapter screen. Step 6 Click Continue on the router Troubleshooting: If you are experiencing problems with the connection signal strength, slow connection speed, not working, you will want to tune your router’s signal by changing router. You do not need to change the channel on the card; it will automatically new channel after you reboot. The only channel that you need to change is the channel of the router. Your router has 11 different channels to choose from. Start with channel 1 and work your way up. Each time you change the channel on the router, make sure that you restart the wireless computer before trying to connect again. Keep going through the channels until you find one that gives you a stable connection. For instructions on changing channels, refer to the documentation that came with your router. Section ...