Votos - 4, Puntuación media: 3.5
(
)
)
|
Resumen del manual
Purpose This Quick Installation Guide tells you how to install your Switch and how to connect it to your Ethernet network. Terms/Usage In this manual, the term “Switch” (first letter upper case) refers to your 24-Port 10/100Mbps Fast Ethernet Switch, and “switch” (first letter lower case) refers to other Ethernet switches. 1.1 Hardware Interface • 24-Port 10/100Mbps auto-negotiation RJ45 Ports • All ports support auto MDI/MDIX, no need to use cross-over cables 2 1.2 Panel 1.2.1 Front Panel The front panel of the Switch consists of LED indicators, and 24 10/100Mbps ports. The figure below shows the front panel of the Switch. Figure 1-1 Front Panel view of the Switch • 10/100Mbps Ports (Port 1~24): These ports support 10/ 100Mbps, and can operate in Half/Full Duplex transfer modes. These ports also support automatic MDI/MDI-X crossover detection, giving true “plug and play” capability. • LED Indicators: Comprehensive LED indicators display the status of the switch and the network (see Section 1.2.3). 1.2.2 Rear Panel Figure 1-2 Rear Panel view of the Switch • AC Power Connector: AC 100~240V, 50~60Hz. 3 NOTICE: Do not envelop Radiator Fan while the Switch is working. 1.2.3 LED indicators information The front panel LEDs provide instant status feedback and help monitoring and troubleshooting when needed. Figure 1-3 Front Panel view of the switch • POWER: Power Indicator LED Color Status Solid Blinking Off POWER Green The Switch is power-on N/A No power 4 • Port 1~24 10/100M Status LEDs LED Color Status Solid Blinking Off LINK/ ACT Green The respective port is successfully connected to an Ethernet network. The port is transmitting or receiving data on the Ethernet network. No link LED Color Status Solid Blinking Off 10/100 M Green The respective port is connected to the 100Mbps Ethernet network. N/A The respective port is connected to the 10Mbps Ethernet network, or no link. 1.3 Technical Specifications Standards • IEEE 802.3 10BASE–T, IEEE 802.3u 100BASE–TX and IEEE 802.3x Flow Control Network Cables • Ethernet: Cables: 2-UTP Cat. 3, 4, 5, Twisted Pair (UTP) 5 • Fast Ethernet: 2-pair UTP Cat. 5, Twisted Pair (UTP) Ports • 24 x 10/100Mbps TX Auto-Negotiation RJ45 Port Access Method • CSMA/CD Transmission Method • Store and Forward MAC Address Table • 8K Built-in Buffer • 1.25M bits Data Transfer Rate** • Ethernet: 10/20Mbps – Half/Full- Duplex • Fast Ethernet: 100/200Mbps – Half/Full Duplex Physical and Environmental • Power Input: 100~240V AC, 50~60Hz • Operation Temperature: 0 °C ~ 50°C • Storage Temperature: -20°C ~ 70°C • Humidity: 5% ~ 90% RH, non-condensing 6 2 Installing the Switch The site where you place the switch may greatly affect its performance. When installing, take the following into your consideration. 2.1 Installation Follow the guidelines below to install the Switch: Install the Switch in a fairly cool and dry place. See the Technical Specifications for the acceptable temperature and humidity operating ranges. Install the Switch on a sturdy, level surface that can support its weight. Connect the power cord to the Switch and the power outlet. The distance is no more than 182cm. Leave at least 10cm (about 4 inches) of space at the front and rear of the Switch for ventilation. 2.2 Desktop or Shelf Installation When installing the Switch on the desktop or shelf, please attach the rubber feet to the Switch. Peel the protective paper on the pads and attach them on the bottom of the Switch (one at each corner). 2.3 Rack Installation The Switch is rack-and can be installed on an EIA 7 19-inch equipment rack. To do this, first install the mounting brackets on the Switch’s side panels (one on each side), secure them with the included screws, and then use the screws provided with the equipment rack to mount the Switch. 2.4 Power on the Switch The Switch has a universal power supply ranging from 100V to 240V AC, 50 ~ 60Hz power source. The AC power connector is located at the rear of the unit adjacent to and the system fan. The switch’s power supply will adjust to the local power source automatically. Connecting the Switch This section describes how to connect the Switch to your 10/100Mbps Fast Ethernet network. 3.1 Connection Your network device (i.e. switch, IP Camera, VoIP) can be connected to a two-pair Category 5 Cable. do not light up 8 making a proper connection, check your network device, the cable, the Switch conditions and connections. 4 Technical Support E-mail: support@airlink101.com Toll-Free: 1-888-746-3238* Web Site: * Free Voice Technical Support is only available within the hardware warranty (1-Year Limited Warranty from the date of purchase). Customer is required to provide invoice as purchase evidence. **Network conditions and environmental factors as well as network overhead lower actual data throughput rate. Copyright © 2009 AirLink101. All rights reserved. AirLink101, the stylized AirLink101 logo, specific product designations, and all other words and logos that ar...