Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
1A 1 Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio technician for help. FCC Caution This equipment must be installed and operated in accordance with provided instructions and a minimum 5 cm spacing must be provided between computer mounted antenna and person’s body (excluding extremities of hands, wrist and feet) during wireless modes of operation. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment. Federal Communication Commission (FCC) Radiation Exposure Statement This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation. 2 1. Introduction The Wireless USB Adapter (hereafter called USB adapter), compliant with IEEE 802.11b/g, is a high-efficiency wireless adapter for wireless networking at home, in office, or in public places. This USB adapter connects directly to any USB-ready desktop/notebook computers, so that you can share files, printers, and high-speed access to the Internet over your existing wireless network easily, without disassembling your computer. The USB adapter has a data rate of up to 54Mbps, and can auto-negotiate to 54, 48, 36, 24, 18, 12, 11, 9, 6, 5.5, 2, 1Mbps to be compatible with any IEEE 802.11b/g device. The USB adapter is compatible with Windows 98SE/ME/2000/XP and can be used in either Ad-hoc mode (computer-to-computer, without a wireless router) or Infrastructure mode (computer-to-wireless router, a wireless router is required). 1.1 Features . With the IEEE 802.11g 2.4GHz (OFDM) standard . High data transfer rate - up to 54Mbps . Supports 64/128/256-bit WEP and WPA data encryption security . Supports peer-to-peer communication among any wireless users, no Access Point required . Automatic fallback increases data security and reliability . Supports the most popular operating systems: Windows 98SE/ME/2000/XP . Portable and mini-size design . Suitable for any IBM-compatible notebook or desktop PC 1.2 Package Contents Before you begin the installation, please check the items of your package. The package should include the following items: . One Wireless USB Adapter . One USB Extension Cable . One Quick Installation Guide . One Driver & Utility CD (with User’s Manual) If any of the above items is missing, contact your supplier as soon as possible. 3 2. Installation Procedures 2.1 Install Utility Software Note: Before installing the utility software, DO NOT insert the USB adapter into your computer. If the adapter is inserted already, Windows will detect the adapter and request for a driver. Click Cancel to quit the wizard and remove the adapter from your computer. Step 1 Insert the provided Driver and Utility CD into your CD drive. Step 2 Click Install Driver from the Setup menu. Note: If the Setup menu does not appear automatically, go to Start, Run, type D:\autorun.exe (where D is the letter of your CD drive) and click OK. 4 Step 3 When the welcome screen appears, click Next. Step 4 Click Next to accept the default destination folder for the software or click Browse to manually select a different destination folder. 5 Step 5 For Windows XP, click Continue Anyway at the Windows Logo Compatibility screen. For Windows 2000, click Yes at the Digital Signature screen. Step 6 Remove the Driver & Utility CD from your CD drive and then restart your computer. 6 2.2 Install Driver Note: In most cases, Windows will automatically install the driver after the computer is restarted. If the Found New Hardware Wizard ap...