Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
The FCR200 responds to commands issued to a set of configured SCSI IDs, and maps these to Fibre Channel AL_PA/LUN values. The following table indicates a possible mapping for SCSI LUN to Fibre Channel AL_PA:LUN. Table 5-2 SCSI-to-Fibre Target:Channel Address Mapping SCSI BUS:TARGET:LUN Fibre Channel AL_PA LUN 0:0:0 0xEF 0 0:1:0 0x02 0 0:2:0 0x04 0 0:3:0 0x08 0 0:4:0 0x0F 0 5-, Understanding the Configuration 62-9301-01 Table 5-2 SCSI-to-Fibre Target:Channel Address Mapping SCSI BUS:TARGET:LUN Fibre Channel AL_PA LUN 0:4:1 0x10 0 0:4:2 0x17 0 0:4:3 0x18 0 The Index Table is edited to represent the desired mapping, and saved to FLASH memory. In addition to configuring the address mapping, SCSI-to-Fibre Channel mode requires that a SCSI interface on the FCR200 be configured to respond to specified SCSI IDs. This is done through the SCSI configuration menu. Target ID’s enabled for the FCR200 must be unique on the SCSI bus, with the exception that the initiator ID used on the FCR200 should also be used as a single target ID. For example, in SCSI-to-Fibre Channel mode, one of the targets must have the same ID as the |Q= Note FCR2°°. The initiator and Target ID’s must be assigned before the address table can be configured. SCSI Host to Fibre Channel Target Configuration 5-9 5-10 Understanding the Configuration 62-9301-01 6 Configuration Configuring the FCR200 ...................................................6-3 Operation Indicators......................................................6-4 Host Device Configuration ................................................6-5 Device Management......................................................6-5 Serial................................................................6-5 Ethernet.............................................................6-6 SNMP...............................................................6-6 Communicating with the FCR200 ...........................................6-6 Setting Up Serial Port Communications..................................6-7 Power Up Menu .........................................................6-8 Perform Configuration...................................................6-10 Baud Rate Configuration .............................................6-11 Fibre Channel Configuration..........................................6-11 SCSI Configuration ..................................................6-12 Ethernet Configuration...............................................6-13 Fibre Channel-to-SCSI Mapping Configuration ..........................6-13 Changing the Fibre Channel-to-SCSI Mapping Mode.....................6-14 SCSI-to-Fibre Channel Mapping Configuration ..........................6-15 Trace Settings Configuration ..........................................6-15 Save Configuration ..................................................6-15 Restore Last Saved Configuration......................................6-15 Reset Configuration to Factory Defaults ................................6-16 Display POST Status.....................................................6-16 Display Trace and Assertion History.......................................6-17 Reboot.................................................................6-17 Download Firmware.....................................................6-18 To Download Firmware ..............................................6-18 Configuring the FCR200’s Ethernet Port....................................6-20 SNMP Configuration ....................................................6-21 Toggle Trap.........................................................6-21 SNMP Configuration with Traps Enabled ..................................6-22 GET and SET Community Names......................................6-22 IP Address for Traps .................................................6-22 Trap Priority........................................................6-22 6-2 Configuration 62-9301-01 Configuring the FCR200 O3 Note Menus are not case sensitive. Enter uppercase and lowercase characters interchangeably when selecting from menus. 0= Note Unless otherwise indicated, all configuration options set do not take effect until the next boot cycle of the FCR200 unit. A menu structure is used to configure the FCR200 through the serial and telnet interfaces. The currently selected menu and the firmware version currently executing will be displayed. Menu items are selected by entering the number of the menu desired, and exited by entering an ‘X’. In general, the configuration options present in the serial interface correspond to those available through SNMP and telnet. The FCR200 Configuration Program allows the user to control many configuration settings through the FCR200 serial interface. Among these are: • Baud rate of the serial port • Fibre Channel address • SCSI initiator and target IDs • Ethernet IP and MAC addresses • Fibre Channel-to-SCSI mapping • SCSI-to-Fi...