Votos - 4, Puntuación media: 4.5
(
)
)
|
Resumen del manual
Configure the Remote Modem To configure the remote modem, you need to change the following settings: • operating mode for the modem, (see “Configure the Remote Operating Mode” on page 66) • WAN parameters, (see “Configure the Remote WAN” on page 67) • LAN parameters, (see “Configure the Remote LAN” on page 69) Configure the Remote Operating Mode Select DSL on the menu bar then select Advance Configuration under [DSL Options]. 2 In the Operating Mode box, select Remote to configure the modem for this mode. 3 Click Apply. MM701G and MM702G User Manual Chapter 7: Implementing a Point-to-Point LAN Extension Configure the Remote WAN Select WAN on the menu bar to access the WAN Configuration page. MM701G and MM702G User Manual Complete a Custom Configuration Select RFC 1483 bridged from the WAN Configuration page to display the following page. 3 In the Session Name box, assign a name to this session. 4 In the Virtual Path ID (VPI 0 - 4,095) box, enter the Virtual Path ID. This must match the Virtual Path ID of the Central-Office modem. 5 In the Virtual Channel ID (VCI 32 - 65,535) box, enter the Virtual Channel ID. This must match the Virtual Channel ID of the Central-Office modem. 6 Click Apply. MM701G and MM702G User Manual Chapter 7: Implementing a Point-to-Point LAN Extension Configure the Remote LAN Select LAN on the menu bar, then select LAN Setup under LAN Options] to access the LAN Configuration page. 2 In the LAN Protocol box, confirm that the protocol is set to Bridged. If the protocol is not set to bridged, it can be changed only through the command-line interface. See Appendix A, “Accessing the Command-Line Interface” for procedures on using this interface to change the LAN protocol. Any device (such as a PC) connecting to the modem LAN interface loses its connection when the modem LAN IP address is changed. After the IP address is changed, you need to specify this new address in the Web browser to reconnect a device. 3 In the IP Address box, enter an available IP address on your subnet. 4 Click Apply. MM701G and MM702G User Manual Complete a Custom Configuration Select Save Changes on the menu bar to access the Save Changes page. Click Save to save the configuration to flash memory. Configure the Central-Office Modem To configure the central-office modem, you need to change the following settings: • operating mode for the modem, (see “Configure the Central-Office Operating Mode” on page 71) • WAN parameters, (see “Configure the Central-Office WAN” on page 72) • LAN parameters, (see “Configure the Central-Office LAN” on page 74) MM701G and MM702G User Manual Chapter 7: Implementing a Point-to-Point LAN Extension Configure the Central-Office Operating Mode Select DSL on the menu bar then select Advance Configuration under [DSL Options]. 2 In the Operating Mode box, select CO to configure the modem for this mode. 3 Click Apply. MM701G and MM702G User Manual Complete a Custom Configuration Configure the Central-Office WAN Select WAN on the menu bar to access the WAN Configuration page. MM701G and MM702G User Manual Chapter 7: Implementing a Point-to-Point LAN Extension Select RFC 1483 bridged from the WAN Configuration page to display the following page. 3 In the Session Name box, assign a name to this session (it can be the same name set up for the Remote modem). 4 In the Virtual Path ID (VPI 0 - 4,095) box, enter the Virtual Path ID. This must match the Virtual Path ID of the Remote modem. 5 In the Virtual Channel ID (VCI 32 - 65,535) box, enter the Virtual Channel ID. This must match the Virtual Channel ID of the Remote modem. 6 Click Apply. MM701G and MM702G User Manual Complete a Custom Configuration Configure the Central-Office LAN Select LAN on the menu bar, then select LAN Setup under LAN Options] to access the LAN Configuration page. 2 In the LAN Protocol box, confirm that the protocol is set to Bridged. If the protocol is not set to bridged, it can be changed only through the command-line interface. See Appendix A, “Accessing the Command-Line Interface” for procedures on using this interface to change the LAN protocol. Any device (such as a PC) connecting to the modem LAN interface loses its connection when the modem LAN IP address is changed. After the IP address is changed, you need to specify this new address in the Web browser to reconnect a device. 3 In the IP Address box, enter an available IP address on your subnet. 4 Click Apply. MM701G and MM702G User Manual Chapter 7: Implementing a Point-to-Point LAN Extension Select Save Changes on the menu bar to access the Save Changes page. Click Save to save the configuration to flash memory. MM701G and MM702G User Manual Verify Connectivity VERIFY CONNECTIVITY After you have performed each of the previous configuration changes, verify back-to-back communication by passing traffic over the WAN session. For example, set up a PC on the LAN-side of the Remote modem and another PC on the LAN-side of the Central-Office modem. Then, transfer a file or...
Otros modelos de este manual:Equipo de red - MM702G (3.34 mb)