Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
• Data Compression – ITU-T V.44, V.42 bis and MNP5 • Fax specs – ITU-T V.17, V.29, V.27 ter, V.21 channel 2 EIA/TIA 578 FAX Class 1, or T.31 Fax Class 1.0 commands • PCI 2.2-compliant • Full Duplex • Tone and Pulse dialing • Auto detect Voice/Data/Fax modes SYSTEM REQUIREMENTS: • x86 compatible PC with a PCI bus expansion slot • CD-ROM drive, Quad speed or faster • Hard Drive with at least 100MB free space • Microsoft Windows® XP, Windows® Vista • Sound card required for Voice and Answering functions CHECK LIST: • Internal PCI Modem • RJ11 Phone Cord • Software & Document CD-ROM • Quick Start Guide (Printed) 2 Hardware Installation: 1. Make sure the power to your PC is turned OFF. 2. Remove the computer’s cover. 3. Select a PCI bus expansion slot for the new adapter. Remove the slot cover 4. Insert the modem into place carefully. Secure the adapter and retaining bracket. 5. Replace the computer’s cover. HARDWARE DESCRIPTION: 3 Software Installation: This guide is intended to help you get started quickly with driver installation in Microsoft Windows. Important Notice: Add second modem or change the modem to an existing PC system, you may proceed a few steps before install the new hardware and software (modem’s driver). The followings are some of the considers: 1. To change a new modem, please remove the existing modem driver, or disable it from Windows® system before you remove the existing hardware. 2. To added second modem, make sure the mainboard that has available IRQ for new devices, and there is no conflict between the others. 3. The driver installation for upgrade system as same as below, if error occur when you proceed step 1, or 2, please consult with your system dealer or the existing hardware manufacturer support. • Windows® XP/ Vista Installation Windows® XP is the latest version out from Microsoft and that has built-in PnP function to detects any new hardware (included this modem) on the system but make sure your motherboard utility driver is installed correctly. 4 After your XP’s desktop loads-up completely, the new hardware wizard will be prompt for your modem. If your windows system has trouble to detect it, or your desktop problem to starts-up after modem added physically, please re-start your windows system again, and make sure the motherboard utility has been setup properly. Insert the manufacturer’s software CD into your CD-ROM and follow the steps to install the modem driver. 1. For WinXP, once you have completed the hardware installation, power on your computer. The Found New Hardware Wizard will show a prompt to search for driver for new hardware found. Click Cancel. 2. After inserting the CD, click on Modem Driver. 3. Select your system Operating System. 4. For Vista system, need to click Allow. 5. Click OK to continue with driver installation FaxTalk Communication SE Note: FaxTalk may detect that your modem as supporting speakerphone, and display speakerphone options within the program. The modem chipset in the Modem may support 5 speakerphone, however, it does not have a microphone or speakerphone socket to operate in speakerphone mode. Installation – 1) Insert CD, Click on Software FaxTalk SE to install software or can use explore CD and go into FaxTalk SE folder , D:\FaxTalk SE, double click on Setup to install. 2) Choose setup language then click ok. 3) At the install shield wizard click next 4) Accept License agreement, click next 5) Type in user name and organization, click next 6) Destination folder, can change or just use the default and click next 7) Click Install to install the program 8) On the Modem Settings window, select Agere Systems PCI soft modem, click next 9) After detection, click next to continue, at the Answer setting window can select your desire setting and click next 10) At the Fax settings window can enter fax information for user and click next 11) Click Finish to finish installation 6 To enable caller id - Open FaxTalk Communicator and select configure> program> modem> Advanced >Distinctive Ring/Caller ID setting Check the box, “Use FaxTalk for Distinctive Ring/ Caller ID service Check the box, “Enable Caller ID detection on incoming calls” Make sure the Caller ID initialization string is set to +vcid=1 Modem Dialing Location If you want to change your dialing location, please follow the instruction as below: Can open FaxTalk Communicator Click on Configure> Dialing Properties, can edit your location Or For Windows XP --- Click Control Panel -> Phone And Modem Options -> Under Dialing Rules click Edit, and then you can change your location. FOR Windows VISTA --- Click Control Panel -> Phone And Modem Options -> Under Dialing Rules click Edit, and then you can change your location. 7 For More information on FaxTalk please check your CD FaxTalk User Guide. Limited Warranty. Manufacturer warrants that the products sold hereunder are free from defects in material and workmanship for a period of two (2) years from manufacturing date. This limited warranty appli...