Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
At that time, Output 1 will be enabled and Output 3 will be disabled. [ON1C6P] , [OFF3C9P] and [SW] 14. [ImOx] This command connects a single input to a single output in the current matrix configuration. Command Format: [ImOxCnUi] m = Input (m= # from 1 to 16) x = Output (x = # from 1 to 8) Cn = Card ID (n = slot # from 1 to max slots) Ui = Unit ID (i = # from 0 to 9) Example: Connect Input 1 to Output 1 for the MT105-100 in slot 5. Send the command [I1O1C5] and Input 1 will be connected to Output 1. 15. [ImO*] This command connects a single input to all the outputs in the current matrix configuration. Command Format: [ImO*CnUi] m = Input (m = # from 1 to 16) Cn = Card ID (n = slot # from 1 to max slots) Ui = Unit ID (i = # from 0 to 9) Example: Connect Input 1 to all outputs for the MT105-100 in slot 5. Send the command [I1O*C5] and Input 1 will be connected to all outputs. 16. [CLR] This command performs a reset of the card and restores settings to the factory defaults. Command Format: [CLRCnUi] Cn = Card ID (n = # from 1 to max slots) Ui = Unit ID (i= # from 0 to 9) 400-0131-004 13 MULTI-TASKER™ Example: Send the command [CLRC4] to reset the card in slot 4. After the reset, the status of C4 will be similar to the following depending on the matrix configuration: Matrix:16X8 In01-Out1 ON In01-Out2 ON In01-Out3 ON In01-Out4 ON In01-Out5 ON In01-Out6 ON In01-Out7 ON In01-Out8 ON Input 1 will be connected to all outputs and all outputs will be enabled. 17. [FBD] This command turns feedback delay on or off. It is necessary when installing some newer cards in older systems. If the system does not receive all of the feedback from the card, the card may be communicating too fast. This command will slow down the card's communication rate. Command Format: [FBDmCnUi] m = Delay (0= no delay, 1= delay 100mS) Cn = Card ID (n = # from 1 to max slots) Ui = Unit ID (i= from 0 to 9) Example: The command [HELPC4] is sent to the card in slot 4. Some of the HELP file is displayed on the screen, but most is missing. Send the command [FBD1C4] to slow down the rate at which the card sends feedback to the system. ID COMMANDS: RSI, SIDn, SIDnCi, SID+, RSN The default Card ID is the same as the card slot number. The next several commands allow the user to change the Card ID to a value other than the slot number. Once the ID is changed, moving the card to another slot will not change the card ID. If a card in slot 4 is set to ID 1, then moved to slot 10, its ID will remain 1. The RSI command forces the installed cards to take their slot number as their ID number, regardless of the slot in which they are installed. Some cards require more than one slot in the Multi-Tasker™ system. As an example, some matrix switcher cards require 4 slots. If there are 5 of these cards installed, they would be numbered C4, C8, C12, C16 and C20. Changing the Card ID allows the user to define the cards as C1, C2, C3, C4 and C5. Another use for changing the Card ID is to be able to use multiple systems without having to set each unit to a different Unit ID. All systems may be left as Unit ID 0 for ease of programming. The cards in the first unit may be numbered 1-10 and in the second unit 11-20. The ID commands work with all Multi-Tasker™ Front Panel systems. However, front panels that have firmware releases prior to the following will not be able to address Card ID's greater than the number of slots in the system: 690-0122-019 = Version 019 or later. 690-0123-005 = Version 005 or later. 690-0124-019 = Version 019 or later. NOTE: Send the command [VER] to the Multi-Tasker™. The system will respond with feedback which includes: 690-0122-019 690-0123-005 690-0124-019 Check the last three digits against the numbers above to determine if the Card ID commands can address all 99 Card ID's. 400-0131-004 14 MULTI-TASKER™ 18. [RSI] This command resets the card ID's in the system. After sending this command, each card ID in the system will match the slot number of the card. If the card is moved to another slot, its ID number will be the new slot number. Command Format: [RSI] Example: Send the command [RSI] to the system with Unit ID 0. The card in slot 1 will have ID 1, the card in slot 2 will have ID 2 and so on. If the card in slot 1 is then moved to slot 4, the card ID will then be 4. 19. [SIDn] This command sets all the cards installed in the Multi-Tasker™ system to the same Card ID. After sending this command, all cards will be addressed with the same ID. Use caution when sending this command to a system with multiple board types. Command Format: [SIDn] n = Card ID (n = # from 1 to 99) Example: Send the command [SID1] to the system. All the cards in the system now have ID 1. Any commands that are sent to Card ID 1 will be received and executed by each card. 20. [SIDnCi] This command sets the Card ID of a single card to a number from 1 to 99. Command Format: [SIDnCi] n = Card ID (n = # from 1 to 99) Ci = Slot Number (i = # from 1 to max slots) Example: Send th...
Otros modelos de este manual:Equipo de red - MT105-100 (976 kb)