Votos - 6, Puntuación media: 3.8
(
)
)
|
Resumen del manual
• Local Time : Display the current system time. • NTP Client : To synchronize the system time with NTP server. • Enable : Check to select NTP client. • Default NTP Server : Select the NTP Server from the drop-down list. • Time Zone : Select a desired time zone from the drop-down list. • Daylight saving time : Enable or disable Daylight saving. If the system time from NTS server seems incorrect, please verify your network settings, like default Gateway and DNS settings Click Save button to save your changes. Click Reboot button to activate your changes 65 4.3.3 Configure UPnP Universal Plug and Play(UPnP) is an architecture to enable pervasive peer-to-peer network connectivity between PCs, intelligent devices and appliances when UPnP is supported. UPnP works on TCP/IP network to enable UPnP devices to connect and access to each other, very well adopted in home networking environment. • UPnP : By default, it’s “Disable”. Select “Enable” or “Disable” of UPnP Service. Click Save button to save changes and click Reboot button to activate changes For UPnP to work in Windows XP, the “APO1000” or “APO1010” must be available in “My Network Places”. If these devices are not available, you should verify that the correct components and services are loaded in Windows XP. Please refer to Appendix D. Using UPnP on Windows XP 66 4.3.4 Configure SNMP Setup SNMP is an application-layer protocol that provides a message format for communication between SNMP managers and agents. By enabling SNMP function, the administrator can obtain the system information remotely. Please click on System -> SNMP Setup and follow the below setting. • SNMP v2c Enable : Check to enable SNMP v2c. • ro community : Set a community string to authorize read-only access. • rw community : Set a community string to authorize read/write access. • SNMP v3 Enable: Check to enable SNMP v3. SNMPv3 supports the highest level SNMP security. • SNMP ro user : Set a community string to authorize read-only access. • SNMP ro password : Set a password to authorize read-only access. • SNMP rw user : Set a community string to authorize read/write access. • SNMP rw password : Set a password to authorize read/write access. • SNMP Trap : Events such as cold start, interface up & down, and association & disassociation will report to an assigned server. 67 • Community : Set a community string required by the remote host computer that will receive trap messages or notices send by the system. • IP : Enter the IP addresses of the remote hosts to receive trap messages. Click Save button to save changes and click Reboot button to activate. 68 4.3.5 Backup / Restore and Reset to Factory Backup current configuration, restore prior configuration or reset back to factory default configuration can be executed via this page. Please click on Utilities -> Profile Setting and follow the below setting. • Save Settings to PC : Click Save button to save the current configuration to a local disk. • Load Settings from PC : Click Browse button to locate a configuration file to restore, and then click Upload button to upload. • Reset To Factory Default : Click Default button to reset back to the factory default settings and expect Successful loading message. Then, click Reboot button to activate. 69 4.3.6 Firmware Upgrade Firmware is the main software image that system needs to respond to requests and to manage real time operations. Firmware upgrades are sometimes required to include new features or bugs fix. It takes around 8 minutes to upgrade due to complexity of firmware. To upgrade system firmware, click Browse button to locate the new firmware, and then click Upgrade button to upgrade. 1. To prevent data loss during firmware upgrade, please back up current settings before proceeding. 2. Do not interrupt during firmware upgrade including power on/off as this may damage system. 70 4.3.7 Network Utility The administrator can diagnose network connectivity via the PING utility. Please click on Utilities -> Network Utility and follow the below setting. • Ping : This utility will help ping other devices on the network to verify connectivity. Ping utility, using ICMP packets, detects connectivity and latency between two network nodes. As result of that, packet loss and latency time are available in the Result field while running the PING test. • Destination IP/Domain : Enter desired domain name, i.e. or IP address of the destination, and click ping button to proceed. The ping result will be shown in the Result field. • Count : By default, it’s 5 and the range is from 1 to 50. It indicates number of connectivity test. 71 4.3.8 Reboot This function allows user to restart system with existing or most current settings when changes are made. Click Reboot button to proceed and take around three minutes to complete. A reminder will be available for remaining time to complete. If power cycle is necessary, please wait till completion of the reboot process. The System Overview page appears ...
Otros modelos de este manual:Equipo de red - APO1000 (3.65 mb)