Votos - 2, Puntuación media: 3
(
)
)
|
Resumen del manual
11) and create the HOSTS.NW file (refer to the documentation of the Ethernet Card). (2) Double click the Management Protocol Selection Tool. Network Printer Manager Protocol Setup Tool window appears. (3) Click Manager Via NetWare/IPX and type the server name in the Preferred NetWare Server box. (4) Click OK. 13 Quick Install Guide (5) Double click the Network Printer Manager icon. The Administration Password window appears. (6) Type the password in the Please enter the administration password box and click OK. Network Printer Manager window appears. (7) Select the server for the Ethernet Card in the Printer Servers list and click Configure Server button. The Server Configuration window appears. (8) Click the NetWare button. NetWare Configuration window appears. (9) Click on Enable Operation check box of Remote Printer. (10) Click OK twice. Proceed to the following “Setup of the Printer Settings in NetWare”. 14 Quick Install Guide Setup of the Printer Settings in NetWare To set the NetWare server, refer to the CD-ROM’s documentation of the Ethernet Card and the documentation of NetWare. Note: • It is recommended to create up to an 8 character name as the remote queue’s name. • Access to the print queue is different from access to the fde server on NetWare. Be sure to give the printer administrator the privilege to access the print queue. • The user which can use the print queue is different from the user which can use the NetWare fde server. Register the user using the print queue. • If using the banner, select ASCff as the data type. To set the client computer, proceed to “Setup of the Client Computer” section (®"P.33). 15 Quick Install Guide Using Windows NT The printer is configured in the following order. 1. Logon to Windows NT as the administrator. 2. Set the TCP/IP of Windows NT. 3. Set the TCP/IP of the Ethernet Card. 4. Set the printer’s setting in Windows NT. 5. Set the client computer. Setting up ТСРЯР in Windows NT Data is printed through the Ethernet Card using TCP/IP protocol. If Windows NT is already configured for TCP/IP protocol, it is not required to perform this section. Proceed to “Setting the TCP/IP of the Ethernet Card” (^P.18). Confirm with the network administrator whether the server’s IP Address for Windows NT is assigned. If TCP/IP protocol is already used for the network, please consult with the network administrator on how to set up the TCP/IP in Windows NT. If not and the network is not connected to the internet, the IP Address can be set freely. However, if you set up TCP/IP protocol first in the network, it is recommended that the IP Address, Subnet Mask and Default Gateway are set as instructed below. IP Address, Subnet Mask and Default Gateway are set when setting the TCP/IP. IP Address can be assigned as follows depending on the lead value (a)~(c). 16 Quick Install Guide (a) IP Address: 010. xxx. xxx. xxx An IP address with a lead value of 010 can have a total of 1677214 possible different combinations. Each xxx value must have a number between 001 -254. Be sure that the IP address is not already assigned to another device. Subnet Mask is 255.000.000.000 and it is not required to set the Default Gateway. (b) IP Address: 172.016.xxx.xxx -172.03l.xxx.xxx An IP address with a lead value from 172.016 to 172.031 can have a total of 65534 possible different combinations. Each xxx value must have a number between 001 - 254. Be sure that the IP address is not already assigned to another device. Subnet Mask is 255.255.000.000 and it is not required to set the Default Gateway. (c) IP Address: 192.168.000.xxx - 192.168.255.xxx An IP address with a lead value from 192.168.000 to 192.168.255 can have a total of 254 possible different combinations. Each xxx value must have a number between 001 - 254. Be sure that the IP address is not already assigned to another device. Subnet Mask is 255.255.255.000 and it is not required to set the Default Gateway. Set the TCP/IP in Windows NT and proceed to the next page “Setting the TCP/IP of the Ethernet Card” 17 Quick Instail Guide Setting the TCP/IP of the Ethernet Card To assign the IP Address If the IP Address is assigned by DHCP, the TCP/IP of the Ethernet Card does not need to be set. Refer to the documentation of Ethernet Card (Install of docs directory in CD-ROM) and Windows NT. Proceed to “Setup of the Client Computer” section (®"P.33). Confirm with the network administrator whether the server’s IP Address for Windows NT is assigned. If TCP/IP protocol is already used for the network, please consult with the network administrator on how to set up the TCP/IP in Windows NT. If not and the network is not connected to the internet, the IP Address can be set freely. However, if you set up TCP/IP protocol first in the network, it is recommended that the IP Address, Subnet Mask and Default Gateway are set. Refer to “Setting up TCP/EP in Windows NT’ (^P.16). Be sure that the lead value of th...