Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
Bring it to your Philips dealer. • Do not cover the product. • Connect the power adapters only to a 220-240 V AC/50 Hz power supply. • The product can cause interference to other equipment. Check if any equipment near the product can be affected before you start using it. EN EN Installation For basic installation, see the quick start guide that came with your Wireless TV Link. y DC 9V ON/OFF 1 2 3 4 DC 9V ON/OFF DC 9V ON/OFF Install the remote control blaster cord 1 Switch off the transmitter (A). 2 Connect the remote control blaster cord (E) to the IR socket. 3 Position the blaster light in front of the video source. See the user manual of the video source for the exact location of the IR sensor on the front panel. 4 Switch on the transmitter (A). 5 Take the remote control of a video source with you. 6 Go to TV2. 7 Switch on TV2. 8 Switch on the receiver (B). 9 Select the correct SCART input on TV2. 10 Operate the video source with its remote control. Installation Installation EN 1 2 3 4 1 2 3 4 Remove interference on TV2 1 Find the CHANNEL switch on the transmitter (A). 2 Set the CHANNEL switch to a different number. 3 Find the CHANNEL switch on the receiver (B). 4 Set the CHANNEL switch to the same number as on the transmitter (A). EN EN Operation Enjoy your Wireless TV Link For basic operation, see the quick start guide that came with your Wireless TV Link. y Watch a cable TV program on TV2 1 Switch on the transmitter (A). 2 Switch on the VCR or DVD recorder. 3 Take the remote control of the VCR or DVD recorder with you. 4 Go to TV2. 5 Switch on TV2. 6 Switch on the receiver (B). 7 Select the channel on the VCR or DVD recorder with its remote control. Your VCR or DVD recorder needs to be connected to the transmitter (A) of the Wireless TV Link and connected to the Cable-TV signal. DC 9V ON/OFF DC 9V ON/OFF Turn off the auto standby mode when you use the VCR or DVD recorder to watch a cable tv program. Refer to the user manual of the VCR or DVD recorder. If the VCR or DVD recorder records a television program, you watch the recorded channel. Watch a video source on TV1 Operate TV1 and the video source as usual. Troubleshooting Troubleshooting EN Problem Tip No image or wrong image on TV1 No image or wrong image on TV2 • Make sure video source is connected to the transmitter (A). • Make sure the transmitter (A) is connected to TV1. • Make sure SCART cables are firmly inserted. • Make sure the video source is switched on. • Make sure the correct SCART input on TV1 is selected. • Make sure SCART cables are firmly inserted. • Make sure the receiver (B) is connected to TV2. • Make sure both receiver (B) and transmitter (A) are switched on. • Make sure the video source is switched on. • Make sure the correct SCART input on TV2 is selected. • If the video source gives proper image on TV1: Make sure the video source gives video signal in CVBS mode. See its user manual • Change the wireless channel that is used for communication. See page 7. • The receiver (B) is out of range of the transmitter (A). The number of walls and ceilings in between the receiver (B) and transmitter (A) restrict the distance. EN EN Troubleshooting Problem Tip Interference in the • Slightly change the position of the image on TV2 receiver (B) or the transmitter (A). • Change the wireless channel that is used for communication. See page 7. • The receiver (B) is out of range of the transmitter (A). The number of walls and ceilings in between the receiver (B) and transmitter (A) restrict the distance. The video sources do not respond to the remote control commands from TV2 • Point the remote control directly to the receiver (B). • Replace the batteries of the remote controls with new ones. • Install the remote control blaster cord (E). See page 6. • The maximum operating distance of the remote control is 5 m. The image of the • Turn off the auto standby mode video source dis-of the video source. See its user appears on TV2 manual. • Follow the instructions to reconnect the video sources. See the quick start guide. Buzzing sound • Slightly change the position of the when you use the receiver or the transmitter until remote control. the buzzing sound stops. • Sometimes it is not possible to solve the problem. Black and white • Check if the SCART connector of image with S-VHS the S-VHS VCR gives signal in VCR. CVBS. See its user manual. Information Information EN Health and safety The product transmits and receives radio waves when it is switched on. The product complies with the standards that are defined for it. The quality of the image can be influenced by the use of microwave ovens. Other wireless systems (Bluetooth, wireless networks etc.) can also have influence on the quality of the image. The product is based on RF technology. Therefore the product can suffer from the same kinds of interference as GSMs, portable radios and other RF-based products. Maintenance and service If your product is defective and needs repair, but your warranty p...