Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
OFF switch on the back of the product 3.Set the CHANNEL switch to the same ! number that on the transmitter (A) 3.2 Enjox All the operations listed on 3.1 and 3.2 ! should have been done1. Switch on TV22. Switch on the receiver (B)3. Select the correct SCART input on ! TV24. Point the remote control of the video ! source to the receiver (B)5. Operate the video source with its ! remote control 6.Check if TV2 shows the image of the ! video source>! The receiver is connected ! correctly 10!Getting startec Note: If the VCR or DVD recorder ! records a television program, you watch ! the recorded channel Note: How to watch a video source on ! TV1? ! Use your TV1 and your video source as ! usual to watch a video source on TV1 3.3 Install the remote control blaster corc The remote control blaster cord ! transmits IR signal to Source devices1. Switch off the transmitter (A) 2.Connect the remote control blaster ! cord (D) to the IR socket 3.Position the blaster light in front of the ! video source. Just put it in front of the ! IR sensor on the front panel Note: See the user manual of the video ! source for the exact location of the IR ! sensor on the front panel 4.Switch on the transmitter (A) 5.If the IR control blaster is well ! installed, you can use your remote ! control to manage your video source 3.4 Remove interference on TV2 When 3.1 and 3.2 are done, you may have ! some interferences1. Find the CHANNEL switch on the ! transmitter (A). There are 4 channels. ! You may have to change the channels ! in case of interferences 2.Set the CHANNEL switch to a ! different number on the transmitter ! (A) in case of interferences 3.Find the CHANNEL switch on the ! receiver (B). 4.Set the CHANNEL switch to the same ! number as on the transmitter (A). Getting startec Technical Dat` Transmitteq System: RF (TV-LINK)! Modulation: FM! Weight: 0.292kg! Dimensions:120X182X40.2mm! Carrier Frequency: 2400~2470MHz! Channels: 4! Radiated Output Power: 10mW! Effective Transmission Range: 40m! Audio Input level: 2V! Video Input level: 1.1V! Power requirements: 9V/500mA! IR Extender Receiver! RF Frequency: 433.92MHz! Receiving Sensitivity: -90 ~ -98 dBm! IR carrier Frequency: 30~57kHz! IR LED Operation Range: !=>3m! Receiveq System: RF (TV-LINK)! Weight: 0.290kg! Dimensions:120X182X40.2mm! Playback frequency range: ! 2400~2470MHz! Channels: 4! Audio S/N ratio: 45dB (at 15m)! Video S/N ratio: 50dB (at 15m)! Audio Output level: 2V! Video Output level: 1.1V! Video Frequency Response:! 50Hz~5.5MHz! Audio frequency response: 40Hz~15kHz! Power Requirements: 9V/500mA! IR Extender Transmitter! IR Frequency: 433.92MHz! RF Output Power: 7~9dBm! IR carrier Frequency: 30~57kHz! IR Sensor Operation Range: !=>7m! Temperature rangd . Operation: Between 0 and 40.C ! (32 to 103.F ). Storage: Between -10 and 70.C ! (14 to 157.F)Relative humiditx . Operation: Up to 90% at 40.C! . Storage: Up to 90% at 40.C! Technical Dat` Frequently asked questionr In this chapter, you will find the most ! frequently asked questions and answers ! about your product No image or wrong image on TV1! . Make sure the video source is ! switched on. Make sure the video source is ! connected to the transmitter (A). Make sure the transmitter (A) is ! connected to TVI. Make sure the transmitter (A) is ! switched on. Make sure SCART cables are firmly ! inserted. Make sure the correct SCART input ! on TVI is selectedNo image or wrong image on TV2! . Make sure SCART cables are firmly ! inserted. Make sure the receiver (B) is ! connected to TV2. Make sure both receiver (B) and ! transmitter (A) are switched on. Make sure the video source is ! switched on. Make sure the correct SCART input ! on TV2 is selected. If the video source gives proper image ! on TVI, make sure the video source ! gives video signal in CVBS mode. Change the wireless channel that is ! used for communicationSee .Remove interference on TV2. on ! page!11. The receiver (B) is out of range of the ! transmitter (A). The number of walls ! and ceilings between the receiver (B) ! and transmitter (A) restricts the ! distanceInterference in the image on TV2! . Slightly change the position of the ! receiver (B) or the transmitter (A). Change the wireless channel that is ! used for communication. ! . See .Remove interference on TV2. on ! page!11 . The receiver (B) is out of range of the ! transmitter (A). The number of walls ! and ceilings between the receiver (B) ! and transmitter (A) restricts the ! distanceThe video sources do not respond to the ! remote control commands from TV2! . Point the remote control directly to ! the receiver (B). Replace the batteries of the remote ! controls with new ones. Install the remote control blaster cord ! (D)See .Install the remote control blaster ! cord. on page!11Note: The maximum operating distance ! of the remote control is 7m Buzzing sound when you use the remote ! control! . Slightly change the position of the ! receiver or the transmitter until the ! buzz...