Votos - 0, Puntuación media: 0
(
)
)
|
Otros manuales para este modelo:
Equipo de red - JWNR2000v2 (3.24 mb)
Equipo de red - JWNR2000v2 (3.03 mb)
Resumen del manual
Place the stand on a level surface. 2. Slide the router onto the stand. Step 1: Step 2: Step 3: Connect your modem. Connect your router. Connect your computer. (not included) Internet DSL or Cable CAUTION: MAKE SURE YOUR MODEM IS TURNED OFF OR UNPLUGGED BEFORE STARTING THE INSTALLATION. Laptop or Desktop Computer Step 4: your modem. in the address bar to completethe setup. Step 6: Configure settings. Open a browser, such as Internet Explorer. If the web Step 5: Power on your router. Wait until the power LED turns solid green. Power on your modem. Wait until your modem cycles on (approximately 2 minutes). Note: If you have a battery-backed modem, press the reset button. In some cases, you may need to remove, then re-insert, the battery to recycleDSL or Cable Modem Ethernet cable N300 Wireless Router (not included) WPS push button page doesn’t display, close and re-open the browser to Power on/off button January 2011 Router Configuration Set up internet connection 1. In your browser address field type and click Enter. 2. When the Welcome screen opens, click Next. It will detect your type of internet connection. Follow the prompts to complete your router Internet connection. Set up wireless security 1. First, assign a name to your wireless network. Choose a name (SSID) that is easy to remember. You might want to write it down in the area provided on the middle panel. (Default is NETGEAR). Click Next. 2. Select the Yes option to add security then select your security method. NETGEAR recommends WPA-PSK [TKIP] + WPA2-PSK [AES ]. 3. Choose a Passphrase. You might want to write it down in the area provided on the middle panel. (Example: HomeNetwork). Click Next. Note: Both your network name (SSID) and passphrase are case sensitive. 4. Review your network settings on the Success page. You may want to print this for your records. Click Next to apply all settings and continue to follow instructions in the next section. Connect Wireless Devices to Your Router 1. Open the software that manages your wireless connections on the wireless device that you want to connect to your router. (For example, on Windows XP, go to Control Panel ->Network Connections, right click the wireless device and select View Available Wireless Networks). 2. The wireless software will scan for all wireless networks in your area. Look for and select the network name that you chose when you set up your router. 3. If your network is secured, you will be prompted for a Passphrase or network key. Enter the Passphrase you selected and click Connect. You are now finished with the installation. Note: If your wireless device supports WPS (WiFi Protected Setup)—NETGEAR calls this method Push 'N' Connect—you might be prompted to press a WPS button on the router instead of entering a Passphrase. If so, go to Step 4. 4. Press the WPS button on the router. It will look similar to or . 5. Within 2 minutes, follow the wireless software instructions on the wireless device to complete the WPS process. The device will then be connected to your router. Repeat this process to add other wireless devices. Note: Your network name, security method and passphrase must be the same on all wireless devices connected to your router. Enter your wireless information here: Wireless Network Name (SSID) ________________________________ Wireless Security Passphrase __________________________________ If you forget your Passphrase, connect a computer to the router using an Ethernet cable and log in to and enter the default User Name (admin) and Password (password). Restore Factory Default: For some routers, you may need to reset the device to its factory default first, then reconfigure your Passphrase. To restore factory defaults, use a paper clip to press the recessed reset button on the back until the Power/Test light blinks. This takes about 10 seconds. Release the button and wait for the router to reboot. Log in with the default username is (admin) and password (password). Note: Restoring factory defaults will erase any customizations and you will lose any configurations saved to the device! Connect Wireless Devices to Your Router 1. Open the software that manages your wireless connections on the wireless device that you want to connect to your router. (For example, on Windows XP, go to Control Panel ->Network Connections, right click the wireless device and select View Available Wireless Networks). 2. The wireless software will scan for all wireless networks in your area. Look for and select the network name that you chose when you set up your router. 3. If your network is secured, you will be prompted for a Passphrase or network key. Enter the Passphrase you selected and click Connect. You are now finished with the installation. Note: If your wireless device supports WPS (WiFi Protected Setup)—NETGEAR calls this method Push 'N' Connect—you might be prompted to press a WPS button on the router inst...